2022 Hyundai Tucson Brake Job Torque Specs

OEM-referenced torque, socket, and thread specs for the 6 brake fasteners you touch on a 2022 Hyundai Tucson brake job — caliper mounting bolts, caliper bracket bolts, slide/guide pins, and rotor hardware, including the Front Brake Caliper Bracket Bolt (torques to 58-72 ft-lbs (78.5-98.1 Nm), 17mm socket, M12x1.25 thread). Every value is safety-critical; verify against your service manual and use a calibrated torque wrench. Full bolt specs for the rest of the vehicle are linked below.

Caliper Mounting Bolts torque — 2022 Hyundai Tucson

On the 2022 Hyundai Tucson, the caliper mounting bolts are: Front Brake Caliper Bolt (torques to 27 Nm, 17mm socket, M12x1.5 thread); Rear Brake Caliper Bolt (torques to 27 Nm, 14mm socket, M10x1.25 thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

Caliper Bracket Bolts torque — 2022 Hyundai Tucson

On the 2022 Hyundai Tucson, the caliper bracket bolts are: Front Brake Caliper Bracket Bolt (torques to 58-72 ft-lbs (78.5-98.1 Nm), 17mm socket, M12x1.25 thread); Rear Brake Caliper Bracket (torques to 69 Nm, 17mm socket, M14x1.5 thread); Front Brake Caliper Bracket (torques to 58-72 ft-lbs (78.5-98.1 Nm), 17mm socket, M14x1.5 thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

Caliper Slide / Guide Pins torque — 2022 Hyundai Tucson

On the 2022 Hyundai Tucson, the caliper slide / guide pins are: Front Brake Caliper Slide Pin (torques to 16-24 ft-lbs (21.6-31.4 Nm), 12mm socket, M10x1.25 thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

How to do a Tucson brake job right

Work one corner at a time so the other side holds a reference. Unbolt the caliper, hang it from the coil with wire (never let it dangle on the hose), and back the caliper bracket bolts out — those are the high-torque fasteners (commonly 80-140 ft-lbs) and are frequently torque-to-yield, so plan to replace them. Clean and lube the slide pins, or replace the pin boots if torn. Apply the specified thread-locker, start every bolt by hand to avoid cross-threading, and make the final pass with a calibrated torque wrench. Pump the pedal to seat the pads before you drive, and re-torque the lug nuts after the wheels go back on.

Tools you need for a Tucson brake job

The 2022 Hyundai Tucson brake job calls for 17mm, 12mm, 14mm sockets, a caliper slide-pin tool or hex/Torx bit set, a torque wrench that covers the high bracket-bolt values, thread-locker, and brake grease for the slide pins. A caliper piston compressor makes seating the new pads far easier. See the recommended tools and replacement hardware linked below.

Related lookups

Loading interactive lookup…