2006 Dodge Charger Suspension & Steering Torque Specs

OEM-referenced torque, socket, and thread specs for the 20 front and rear suspension and steering fasteners on the 2006 Dodge Charger — including the Rear Toe Link Knuckle Bolt (torques to 60 ft-lbs (81 Nm)). Every value is safety-critical; verify against your service manual and use a calibrated torque wrench. Full bolt specs for the rest of the vehicle are linked below.

Control Arms & Ball Joints torque — 2006 Dodge Charger

On the 2006 Dodge Charger, the control arms & ball joints fasteners are: Rear Toe Link Knuckle Bolt (torques to 60 ft-lbs (81 Nm)); Front Lower Ball Joint Nut (torques to 50 ft-lbs (68 Nm) + 90 deg); Front Upper Control Arm Frame Nut (torques to 55 ft-lbs (75 Nm)); Front Lower Control Arm Cradle Nut (torques to 130 ft-lbs (176 Nm)); Rear Camber Link Knuckle Bolt (torques to 72 ft-lbs (98 Nm)); Rear Tension Link Knuckle Bolt (torques to 72 ft-lbs (98 Nm)); Rear Compression Link Knuckle Bolt (torques to 60 ft-lbs (81 Nm)); Front Upper Ball Joint Nut (torques to 35 ft-lbs (47 Nm) + 90 deg). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Struts, Shocks & Springs torque — 2006 Dodge Charger

On the 2006 Dodge Charger, the struts, shocks & springs fasteners are: Front Shock Absorber Upper Nut (torques to 20 ft-lbs (27 Nm)); Rear Shock Absorber Lower Nut (torques to 53 ft-lbs (72 Nm)); Rear Spring Link Knuckle Nut (torques to 102 ft-lbs (138 Nm)); Front Shock Absorber Shaft Nut (torques to 70 ft-lbs (95 Nm)); Rear Shock Absorber Upper Bolt (torques to 38 ft-lbs (52 Nm)); Front Shock Absorber Lower Bolt (torques to 128 ft-lbs (174 Nm)); Front Tension Strut Ball Joint Nut (torques to 50 ft-lbs (68 Nm) + 90 deg). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Sway Bar & Stabilizer Links torque — 2006 Dodge Charger

On the 2006 Dodge Charger, the sway bar & stabilizer links fasteners are: Rear Sway Bar Link Nut (torques to 45 ft-lbs (61 Nm)); Front Sway Bar Link Nut (torques to 95 ft-lbs (128 Nm)). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Steering (Tie Rods & Linkage) torque — 2006 Dodge Charger

On the 2006 Dodge Charger, the steering (tie rods & linkage) fasteners are: Outer Tie Rod End Nut (torques to 63 ft-lbs (85 Nm)); Steering Gear Mounting Bolt (torques to 70 ft-lbs (95 Nm)). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Wheel Hub & Bearing torque — 2006 Dodge Charger

On the 2006 Dodge Charger, the wheel hub & bearing fasteners are: Front Hub Bearing Bolt (torques to 50 ft-lbs (68 Nm)). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

How to torque Charger suspension & steering fasteners

Torque suspension and steering fasteners with the vehicle at ride height (wheels loaded) wherever a bushing is involved — tightening a control-arm or sway-bar bushing bolt with the suspension hanging pre-loads the rubber and it fails early. Clean the threads, start every fastener by hand to avoid cross-threading, and make the final pass with a calibrated torque wrench rather than an impact gun. Ball-joint and tie-rod castle nuts take a new cotter pin; never back a castle nut off to line up the hole — only tighten to the next slot.

Related lookups

Loading interactive lookup…