1987 Ford F-250 Lug Nut Torque & Bolt Specs

The 1987 Ford F-250 lug nut torque is 165 ft-lbs (224 Nm), tightened with a 15/16" socket on M14x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 165 ft-lbs (224 Nm) · Socket size: 15/16" · Thread: M14x1.5.

This page is the OEM-referenced fastener summary for the 1987 Ford F-250. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Ford lug-nut torque varies more by chassis than most makes — 100 ft-lbs for Focus/Fusion/Fiesta, 150 ft-lbs for half-ton F-150, and 165 ft-lbs for Super Duty F-250/F-350. F-150s from 2004-2014 use a 21mm OEM socket, while 2015+ aluminum-body trucks moved to the larger 22mm. Ford torque-to-yield (TTY) head bolts are standard from the early 2000s — do not reuse them, ever.

Common fastener categories on the 1987 Ford F-250

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

Heads up for 1987 Ford F-250 owners: Vehicles this age frequently have seized fasteners due to thread corrosion. Apply penetrating oil (PB Blaster, Kroil) 24 hours before any wrenching, and have a thread chaser on hand. Lug studs are particularly prone to thread damage at this age; if a nut spins on without engaging, the stud is stretched and must be replaced before the wheel goes back on.

Tools you will need

SAE socket set (1/4"-7/8"), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 1987 Ford F-250?

The OEM-specified lug-nut torque for the 1987 Ford F-250 is 165 ft-lbs (224 Nm), using a 15/16" socket on M14x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 1987 Ford F-250 lug nuts?

The 1987 Ford F-250 uses a 15/16" socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 1987 Ford F-250 fasteners metric or SAE?

SAE inch is the standard for this vehicle. Most fasteners on this vehicle are SAE inch, common sizes 1/4", 5/16", 3/8", 7/16", 1/2". Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Ford F-250 years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

All 9 1987 Ford F-250 fastener specs

Per-bolt torque, wrench size, and thread spec for the 1987 Ford F-250, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Brakes — 1987 Ford F-250

Brake fasteners on the 1987 Ford F-250 — caliper bracket, slide pins, and banjo bolt torque follow. Brake rotor retaining clip tightens to Remove and discard, takes a N/A driver, runs on N/A threads, located at the wheel studs.

Engine — 1987 Ford F-250

Engine bolt-by-bolt torque for the 1987 Ford F-250, including the long block, valve covers, and intake. The oil drain plug uses a 1/2" Socket drive on a M14x1.5 thread, torqued to 15-25 ft-lbs at the oil pan. At the cylinder head to block, the cylinder head bolt torques to Follow sequence (Varies drive, Varies thread).

Drivetrain — 1987 Ford F-250

Drivetrain and driveline fasteners for the 1987 Ford F-250 — axle, transmission, and differential plugs. At the all four wheels, the lug nuts torques to 165 ft-lbs (224 Nm) (15/16" drive, M14x1.5 thread). For the driveshaft to axle/transmission, plan for a 12mm or 1/2" tool on a 5/16"-24 stud; final torque is 15-20 ft-lbs (driveshaft u-joint strap bolt).

Suspension — 1987 Ford F-250

Suspension and chassis fastener torque for the 1987 Ford F-250 — strut, control arm, and sway bar values. For the axle to leaf spring, plan for a 1-1/8" or 24mm tool on a 9/16"-18 or 5/8"-18 stud; final torque is 90-120 ft-lbs (leaf spring u-bolt nut). Shock absorber nut (upper) tightens to 25-35 ft-lbs, takes a 15mm or 18mm driver, runs on M10 or M12 threads, located at the top of shock mount.

Body — 1987 Ford F-250

Body fasteners on the 1987 Ford F-250. Fender bolt tightens to 8-12 ft-lbs, takes a 10mm or 13mm driver, runs on M6x1.0 or M8x1.25 threads, located at the engine bay & door jamb. The bed mounting bolt uses a T-55 Torx or 18mm drive on a M12x1.75 thread, torqued to 50-60 ft-lbs at the truck bed to frame.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 1987 Ford F-250 numbers above.

Loading the interactive 1987 Ford F-250 fastener lookup with per-bolt filtering, part links, and torque tools…