2016 John Deere 318g Bolt Sizes & Torque Specs
Free OEM-referenced torque and bolt specs for the 2016 John Deere 318g.
This page is the OEM-referenced fastener summary for the 2016 John Deere 318g. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.
For the 2016 John Deere 318g, fasteners follow metric standards typical of late-model John Deere engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).
Common fastener categories on the 2016 John Deere 318g
- Wheel / lug nut torque and thread spec (covered above)
- Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
- Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
- Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
- Suspension control arm, sway bar, tie rod end and ball joint torque
- Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
- Differential cover bolts (RWD/4WD only) and transfer case fasteners
Repair guidance for this model year
For 2016 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.
Tools you will need
- Metric socket set (8mm-22mm), 6-point impact-rated
- Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
- Breaker bar (24" minimum) for initial loosening
- Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
- Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly
Frequently asked questions
What is the lug nut torque on a 2016 John Deere 318g?
Manufacturer-specified torque values for the 2016 John Deere 318g are in the factory service manual or owner's handbook. WhatSizeBolt sources values from manufacturer literature and verifies against community data — if we do not have this exact year listed, check the John Deere brand page for the closest model year.
What socket size do I need for the 2016 John Deere 318g lug nuts?
Most modern John Deere vehicles use a 19mm or 21mm socket. Older John Deere models from before 2000 may use a 13/16" SAE socket on certain trims. Confirm against the actual lug before purchasing aftermarket wheels.
Are the 2016 John Deere 318g fasteners metric or SAE?
Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.
Other John Deere 318g years
Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.
- 2024 John Deere 318g lug nut torque
- 2023 John Deere 318g lug nut torque
- 2022 John Deere 318g lug nut torque
- 2021 John Deere 318g lug nut torque
- 2020 John Deere 318g lug nut torque
- 2019 John Deere 318g lug nut torque
- 2018 John Deere 318g lug nut torque
- 2017 John Deere 318g lug nut torque
- 2015 John Deere 318g lug nut torque
- 2014 John Deere 318g lug nut torque
All 6 2016 John Deere 318g fastener specs
Per-bolt torque, wrench size, and thread spec for the 2016 John Deere 318g, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.
Engine — 2016 John Deere 318g
Engine bolt-by-bolt torque for the 2016 John Deere 318g, including the long block, valve covers, and intake. For the engine oil sump, plan for a 22mm tool on a M16x1.5 stud; final torque is 29–36 ft-lbs (40–49 Nm) (engine oil drain plug).
Drivetrain — 2016 John Deere 318g
Drivetrain and driveline fasteners for the 2016 John Deere 318g — axle, transmission, and differential plugs. Final drive drain plug tightens to 35–40 ft-lbs (48–54 Nm), takes a 24mm driver, runs on M18x1.5 threads, located at the final drive gear box (one per side).
Undercarriage — 2016 John Deere 318g
Undercarriage fasteners on the 2016 John Deere 318g. The track tension idler bolt uses a 24mm drive on a M16x2.0 thread, torqued to 155 ft-lbs (210 Nm) at the track idler mounting. At the drive sprocket to final drive (6 bolts per side), the sprocket mounting bolt torques to 155 ft-lbs (210 Nm) (24mm drive, M16x2.0 thread).
Safety — 2016 John Deere 318g
Safety fasteners on the 2016 John Deere 318g. At the rops cab/frame mounting (4 bolts), the rops mounting bolt torques to 155 ft-lbs (210 Nm) (24mm drive, M16x2.0 thread).
Attachment — 2016 John Deere 318g
Attachment fasteners on the 2016 John Deere 318g. For the loader bucket attachment pins, plan for a 24mm tool on a M16x2.0 stud; final torque is 140 ft-lbs (190 Nm) (loader bucket pin retaining bolt).
New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2016 John Deere 318g numbers above.
Loading the interactive 2016 John Deere 318g fastener lookup with per-bolt filtering, part links, and torque tools…