2019 John Deere 35g Bolt Sizes & Torque Specs
Free OEM-referenced torque and bolt specs for the 2019 John Deere 35g.
This page is the OEM-referenced fastener summary for the 2019 John Deere 35g. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.
For the 2019 John Deere 35g, fasteners follow metric standards typical of late-model John Deere engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).
Common fastener categories on the 2019 John Deere 35g
- Wheel / lug nut torque and thread spec (covered above)
- Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
- Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
- Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
- Suspension control arm, sway bar, tie rod end and ball joint torque
- Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
- Differential cover bolts (RWD/4WD only) and transfer case fasteners
Repair guidance for this model year
For 2019 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.
Tools you will need
- Metric socket set (8mm-22mm), 6-point impact-rated
- Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
- Breaker bar (24" minimum) for initial loosening
- Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
- Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly
Frequently asked questions
What is the lug nut torque on a 2019 John Deere 35g?
Manufacturer-specified torque values for the 2019 John Deere 35g are in the factory service manual or owner's handbook. WhatSizeBolt sources values from manufacturer literature and verifies against community data — if we do not have this exact year listed, check the John Deere brand page for the closest model year.
What socket size do I need for the 2019 John Deere 35g lug nuts?
Most modern John Deere vehicles use a 19mm or 21mm socket. Older John Deere models from before 2000 may use a 13/16" SAE socket on certain trims. Confirm against the actual lug before purchasing aftermarket wheels.
Are the 2019 John Deere 35g fasteners metric or SAE?
Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.
Other John Deere 35g years
Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.
- 2024 John Deere 35g lug nut torque
- 2023 John Deere 35g lug nut torque
- 2022 John Deere 35g lug nut torque
- 2021 John Deere 35g lug nut torque
- 2020 John Deere 35g lug nut torque
- 2018 John Deere 35g lug nut torque
- 2017 John Deere 35g lug nut torque
- 2016 John Deere 35g lug nut torque
- 2015 John Deere 35g lug nut torque
- 2014 John Deere 35g lug nut torque
- 2013 John Deere 35g lug nut torque
→ 2019 John Deere 35g oil drain plug torque & size
All 7 2019 John Deere 35g fastener specs
Per-bolt torque, wrench size, and thread spec for the 2019 John Deere 35g, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.
Engine — 2019 John Deere 35g
Engine bolt-by-bolt torque for the 2019 John Deere 35g, including the long block, valve covers, and intake. At the engine, the engine oil drain plug torques to 22 ft-lbs (30 Nm) (17mm drive, M14x1.5 thread).
Drivetrain — 2019 John Deere 35g
Drivetrain and driveline fasteners for the 2019 John Deere 35g — axle, transmission, and differential plugs. For the drivetrain, plan for a 24mm tool on a M18x1.5 stud; final torque is 30 ft-lbs (final drive drain plug).
Body — 2019 John Deere 35g
Body fasteners on the 2019 John Deere 35g. Rops/canopy bolt tightens to 133 ft-lbs, takes a 24mm driver, runs on M16x2.0 threads, located at the body.
Undercarriage — 2019 John Deere 35g
Undercarriage fasteners on the 2019 John Deere 35g. The sprocket bolt uses a 24mm drive on a M16x2.0 thread, torqued to 133 ft-lbs at the undercarriage. At the undercarriage, the track bolt torques to 133 ft-lbs (180 Nm) (24mm drive, M16x2.0 thread).
Attachment — 2019 John Deere 35g
Attachment fasteners on the 2019 John Deere 35g. At the attachment, the bucket tooth retaining bolt torques to 133 ft-lbs (24mm drive, M16x2.0 thread). For the attachment, plan for a 24mm tool on a M16x2.0 stud; final torque is 133 ft-lbs (swing bearing bolt).
New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2019 John Deere 35g numbers above.
Loading the interactive 2019 John Deere 35g fastener lookup with per-bolt filtering, part links, and torque tools…