1995 Land Rover Discovery Lug Nut Torque & Bolt Specs

The 1995 Land Rover Discovery lug nut torque is 103 ft-lbs (140 Nm), tightened with a 22mm socket on M14x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 103 ft-lbs (140 Nm) · Socket size: 22mm · Thread: M14x1.5.

This page is the OEM-referenced fastener summary for the 1995 Land Rover Discovery. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 1995 Land Rover Discovery, fasteners follow metric standards typical of 1990s-era Land Rover engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 1995 Land Rover Discovery

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

Heads up for 1995 Land Rover Discovery owners: Vehicles this age frequently have seized fasteners due to thread corrosion. Apply penetrating oil (PB Blaster, Kroil) 24 hours before any wrenching, and have a thread chaser on hand. Lug studs are particularly prone to thread damage at this age; if a nut spins on without engaging, the stud is stretched and must be replaced before the wheel goes back on.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 1995 Land Rover Discovery?

The OEM-specified lug-nut torque for the 1995 Land Rover Discovery is 103 ft-lbs (140 Nm), using a 22mm socket on M14x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 1995 Land Rover Discovery lug nuts?

The 1995 Land Rover Discovery uses a 22mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 1995 Land Rover Discovery fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Land Rover Discovery years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 1995 Land Rover Discovery oil drain plug torque & size

All 22 1995 Land Rover Discovery fastener specs

Per-bolt torque, wrench size, and thread spec for the 1995 Land Rover Discovery, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 1 of the 22 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Wheels — 1995 Land Rover Discovery

Wheel and lug nut spec for the 1995 Land Rover Discovery. At the wheel hub, the wheel lug nut torques to 103 ft-lbs (140 Nm) (22mm drive, M14x1.5 thread).

Engine — 1995 Land Rover Discovery

Engine bolt-by-bolt torque for the 1995 Land Rover Discovery, including the long block, valve covers, and intake. For the oil pan, plan for the right driver; final torque is 24 ft-lbs (33 Nm) (oil drain plug). Confirmed against manufacturer service literature.

Body — 1995 Land Rover Discovery

Body fasteners on the 1995 Land Rover Discovery. Rear skid plate mounting bolt tightens to 37 ft-lbs, takes a 17mm driver, runs on M10x1.5 threads, located at the transfer case/differential skid plate. The skid plate mounting nut uses a 17mm drive on a M10x1.5 thread, torqued to 37 ft-lbs at the frame mount points. At the engine/transmission skid plate, the front skid plate mounting bolt torques to 37 ft-lbs (17mm drive, M10x1.5 thread).

Body/Exterior — 1995 Land Rover Discovery

Body/Exterior fasteners on the 1995 Land Rover Discovery. The undertray speed nut/clip nut (m8 u-clip) (m8 u-clip) uses a 13mm drive on a M8 U-Clip thread, torqued to Hand Tight at the engine undertray/splash shield. At the engine undertray/splash shield, the plastic trim rivet (8mm) (n/a - push rivet) (n/a - push rivet) torques to Hand Press (Hand Tool drive, N/A - Push Rivet thread). For the skid plate/undertray, plan for a N/A tool on a M10 stud; final torque is 37 ft-lbs (skid plate spacer washer). Skid plate mounting bolt (m10) (m10x1.5) (m10x1.5) tightens to 25-30 ft-lbs, takes a 17mm driver, runs on M10x1.5 threads, located at the engine undertray/splash shield. The undertray speed nut/clip nut (m8 u-clip) uses a 13mm drive on a M8 U-Clip thread, torqued to Hand Tight at the engine undertray/splash shield. At the engine undertray/splash shield, the plastic trim rivet (8mm) (n/a - push rivet) torques to Hand Press (Hand Tool drive, N/A - Push Rivet thread). For the engine undertray/splash shield, plan for a Phillips/Flathead tool on a 6.5mm Screw Thread stud; final torque is Hand Tight (plastic screw fit rivet (6.5mm) (6.5mm screw thread) (6.5mm screw thread)). Undertray push pin clip (n/a - push pin) (n/a - push pin) tightens to Hand Press, takes a Hand Tool driver, runs on N/A - Push Pin threads, located at the engine undertray/splash shield. The bumper/engine bay shield clip (n/a - clip) (n/a - clip) uses a Hand Tool drive on a N/A - Clip thread, torqued to Hand Tight at the engine undertray/splash shield. At the front bumper frame, the oem brush guard mounting nut torques to 37 ft-lbs (17mm drive, M10x1.5 thread). For the engine undertray/splash shield, plan for a N/A - Washer tool on a M10/M8 Compatible stud; final torque is N/A (skid plate fender washer (m10/m8 compatible) (m10/m8 compatible)). Undertray push fit rivet clip (9mm) (n/a - push rivet) (n/a - push rivet) tightens to Hand Press, takes a Hand Tool driver, runs on N/A - Push Rivet threads, located at the engine undertray/splash shield. The engine shield undertray bolt (m8x1.25) (m8x1.25) uses a 13mm drive on a M8x1.25 thread, torqued to 15-20 ft-lbs at the engine undertray/splash shield. At the engine undertray/splash shield, the transmission shield bolt (m8x1.25) (m8x1.25) torques to 15-20 ft-lbs (13mm drive, M8x1.25 thread). For the skid plate/undertray, plan for a 10mm tool on a M10 stud; final torque is 37 ft-lbs (skid plate fender washer). Oem brush guard mounting bolt tightens to 37 ft-lbs, takes a 17mm driver, runs on M10x1.5 threads, located at the front bumper frame. The undertray push pin clip uses a N/A drive on a 9mm thread, torqued to Hand tight at the undertray/splash shield.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 1995 Land Rover Discovery numbers above.

Loading the interactive 1995 Land Rover Discovery fastener lookup with per-bolt filtering, part links, and torque tools…