1999 Land Rover Range Rover Lug Nut Torque & Bolt Specs

The 1999 Land Rover Range Rover lug nut torque is 103 ft-lbs (140 Nm), tightened with a 22mm socket on M14x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 103 ft-lbs (140 Nm) · Socket size: 22mm · Thread: M14x1.5.

This page is the OEM-referenced fastener summary for the 1999 Land Rover Range Rover. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 1999 Land Rover Range Rover, fasteners follow metric standards typical of 1990s-era Land Rover engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 1999 Land Rover Range Rover

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

Heads up for 1999 Land Rover Range Rover owners: Vehicles this age frequently have seized fasteners due to thread corrosion. Apply penetrating oil (PB Blaster, Kroil) 24 hours before any wrenching, and have a thread chaser on hand. Lug studs are particularly prone to thread damage at this age; if a nut spins on without engaging, the stud is stretched and must be replaced before the wheel goes back on.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 1999 Land Rover Range Rover?

The OEM-specified lug-nut torque for the 1999 Land Rover Range Rover is 103 ft-lbs (140 Nm), using a 22mm socket on M14x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 1999 Land Rover Range Rover lug nuts?

The 1999 Land Rover Range Rover uses a 22mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 1999 Land Rover Range Rover fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Land Rover Range Rover years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

All 20 1999 Land Rover Range Rover fastener specs

Per-bolt torque, wrench size, and thread spec for the 1999 Land Rover Range Rover, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 1999 Land Rover Range Rover

Wheel and lug nut spec for the 1999 Land Rover Range Rover. Wheel lug nut tightens to 103 ft-lbs (140 Nm), takes a 22mm driver, runs on M14x1.5 threads, located at the wheel hub.

Engine — 1999 Land Rover Range Rover

Engine bolt-by-bolt torque for the 1999 Land Rover Range Rover, including the long block, valve covers, and intake. The oil drain plug, torqued to 30 ft-lbs (41 Nm) at the oil pan.

Body — 1999 Land Rover Range Rover

Body fasteners on the 1999 Land Rover Range Rover. At the frame mount points, the skid plate mounting nut torques to 37 ft-lbs (17mm drive, M10x1.5 thread). For the transfer case/differential skid plate, plan for a 17mm tool on a M10x1.5 stud; final torque is 37 ft-lbs (rear skid plate mounting bolt). Front skid plate mounting bolt tightens to 37 ft-lbs, takes a 17mm driver, runs on M10x1.5 threads, located at the engine/transmission skid plate.

Body/Exterior — 1999 Land Rover Range Rover

Body/Exterior fasteners on the 1999 Land Rover Range Rover. For the front bumper frame, plan for a 17mm tool on a M10x1.5 stud; final torque is 37 ft-lbs (oem brush guard mounting bolt). Plastic trim rivet (8mm) (n/a - push rivet) tightens to Hand Press, takes a Hand Tool driver, runs on N/A - Push Rivet threads, located at the engine undertray/splash shield. The skid plate fender washer (m10/m8 compatible) uses a N/A - Washer drive on a M10/M8 Compatible thread, torqued to N/A at the engine undertray/splash shield. At the engine undertray/splash shield, the engine shield undertray bolt (m8x1.25) torques to 15-20 ft-lbs (13mm drive, M8x1.25 thread). For the engine undertray/splash shield, plan for a Hand Tool tool on a N/A - Push Rivet stud; final torque is Hand Press (undertray push fit rivet clip (9mm) (n/a - push rivet)). Bumper/engine bay shield clip (n/a - clip) tightens to Hand Tight, takes a Hand Tool driver, runs on N/A - Clip threads, located at the engine undertray/splash shield. The skid plate spacer washer uses a N/A drive on a M10 thread, torqued to 37 ft-lbs at the skid plate/undertray. At the engine undertray/splash shield, the undertray push pin clip (n/a - push pin) torques to Hand Press (Hand Tool drive, N/A - Push Pin thread). For the engine undertray/splash shield, plan for a 13mm tool on a M8x1.25 stud; final torque is 15-20 ft-lbs (transmission shield bolt (m8x1.25)). Skid plate fender washer tightens to 37 ft-lbs, takes a 10mm driver, runs on M10 threads, located at the skid plate/undertray. The undertray push pin clip uses a N/A drive on a 9mm thread, torqued to Hand tight at the undertray/splash shield. At the front bumper frame, the oem brush guard mounting nut torques to 37 ft-lbs (17mm drive, M10x1.5 thread). For the engine undertray/splash shield, plan for a Phillips/Flathead tool on a 6.5mm Screw Thread stud; final torque is Hand Tight (plastic screw fit rivet (6.5mm) (6.5mm screw thread)). Undertray speed nut/clip nut (m8 u-clip) tightens to Hand Tight, takes a 13mm driver, runs on M8 U-Clip threads, located at the engine undertray/splash shield. The skid plate mounting bolt (m10) (m10x1.5) uses a 17mm drive on a M10x1.5 thread, torqued to 25-30 ft-lbs at the engine undertray/splash shield.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 1999 Land Rover Range Rover numbers above.

Loading the interactive 1999 Land Rover Range Rover fastener lookup with per-bolt filtering, part links, and torque tools…