1959 Land Rover Series Ii Lug Nut Torque & Bolt Specs
The 1959 Land Rover Series Ii lug nut torque is 103 ft-lbs (140 Nm) on M14x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.
Lug nut torque: 103 ft-lbs (140 Nm) · Thread: M14x1.5.
This page is the OEM-referenced fastener summary for the 1959 Land Rover Series Ii. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.
For the 1959 Land Rover Series Ii, fasteners follow metric standards typical of classic Land Rover engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).
Common fastener categories on the 1959 Land Rover Series Ii
- Wheel / lug nut torque and thread spec (covered above)
- Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
- Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
- Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
- Suspension control arm, sway bar, tie rod end and ball joint torque
- Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
- Differential cover bolts (RWD/4WD only) and transfer case fasteners
Repair guidance for this model year
Heads up for 1959 Land Rover Series Ii owners: Vehicles this age frequently have seized fasteners due to thread corrosion. Apply penetrating oil (PB Blaster, Kroil) 24 hours before any wrenching, and have a thread chaser on hand. Lug studs are particularly prone to thread damage at this age; if a nut spins on without engaging, the stud is stretched and must be replaced before the wheel goes back on.
Tools you will need
- Metric socket set (8mm-22mm), 6-point impact-rated
- Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
- Breaker bar (24" minimum) for initial loosening
- Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
- Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly
Frequently asked questions
What is the lug nut torque on a 1959 Land Rover Series Ii?
The OEM-specified lug-nut torque for the 1959 Land Rover Series Ii is 103 ft-lbs (140 Nm) on M14x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.
What socket size do I need for the 1959 Land Rover Series Ii lug nuts?
Most modern Land Rover vehicles use a 19mm or 21mm socket. Older Land Rover models from before 2000 may use a 13/16" SAE socket on certain trims. Confirm against the actual lug before purchasing aftermarket wheels.
Are the 1959 Land Rover Series Ii fasteners metric or SAE?
Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.
Other Land Rover Series Ii years
Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.
- 1961 Land Rover Series Ii lug nut torque
- 1960 Land Rover Series Ii lug nut torque
- 1958 Land Rover Series Ii lug nut torque
All 1 1959 Land Rover Series Ii fastener specs
Per-bolt torque, wrench size, and thread spec for the 1959 Land Rover Series Ii, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.
Wheels — 1959 Land Rover Series Ii
Wheel and lug nut spec for the 1959 Land Rover Series Ii. At the all wheels, the lug nut torques to 103 ft-lbs (140 Nm) (M14x1.5 thread).
New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 1959 Land Rover Series Ii numbers above.
Loading the interactive 1959 Land Rover Series Ii fastener lookup with per-bolt filtering, part links, and torque tools…