2001 Mercedes Benz Slk 230 Lug Nut Torque & Bolt Specs

The 2001 Mercedes Benz Slk 230 lug nut torque is 81 ft-lbs (110 Nm), tightened with a 17mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 81 ft-lbs (110 Nm) · Socket size: 17mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2001 Mercedes Benz Slk 230. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 2001 Mercedes Benz Slk 230, fasteners follow metric standards typical of mid-2000s Mercedes Benz engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 2001 Mercedes Benz Slk 230

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2001 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2001 Mercedes Benz Slk 230?

The OEM-specified lug-nut torque for the 2001 Mercedes Benz Slk 230 is 81 ft-lbs (110 Nm), using a 17mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2001 Mercedes Benz Slk 230 lug nuts?

The 2001 Mercedes Benz Slk 230 uses a 17mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2001 Mercedes Benz Slk 230 fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Mercedes Benz Slk 230 years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

All 11 2001 Mercedes Benz Slk 230 fastener specs

Per-bolt torque, wrench size, and thread spec for the 2001 Mercedes Benz Slk 230, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 2001 Mercedes Benz Slk 230

Wheel and lug nut spec for the 2001 Mercedes Benz Slk 230. For the wheel hub, plan for a 17mm tool on a M12x1.5 stud; final torque is 81 ft-lbs (110 Nm) (wheel bolt).

Engine — 2001 Mercedes Benz Slk 230

Engine bolt-by-bolt torque for the 2001 Mercedes Benz Slk 230, including the long block, valve covers, and intake. Engine cover mounting bolt (m8x1.25) tightens to 18 ft-lbs, takes a 13mm driver, runs on M8x1.25 threads, located at the engine cover. The oil drain plug, torqued to 18 ft-lbs (24 Nm) at the oil pan.

Undertray — 2001 Mercedes Benz Slk 230

Undertray fasteners on the 2001 Mercedes Benz Slk 230. The splash shield rivet clip (n/a) uses a Hand Press drive on a N/A thread, torqued to Hand tight at the splash shield. At the undertray edges, the undertray push pin clip (n/a) torques to Hand tight (Hand Press drive, N/A thread). For the undertray access panels, plan for a 13mm tool on a M8x1.25 stud; final torque is 15 ft-lbs (speed nut / u-clip). Splash shield mounting bolt (m8x1.25) tightens to 18 ft-lbs, takes a 13mm driver, runs on M8x1.25 threads, located at the front splash shield. The rear undertray mounting bolt (m8x1.25) uses a 13mm drive on a M8x1.25 thread, torqued to 25 ft-lbs at the rear undertray. At the undertray center junction, the center section connector bolt torques to 18 ft-lbs (13mm drive, M8x1.25 thread). For the front undertray, plan for a 13mm tool on a M8x1.25 stud; final torque is 25 ft-lbs (front undertray mounting bolt (m8x1.25)). Wheel arch liner rivet tightens to N/A, takes a Hand Press driver, runs on N/A threads, located at the wheel arch / fender liner.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2001 Mercedes Benz Slk 230 numbers above.

Loading the interactive 2001 Mercedes Benz Slk 230 fastener lookup with per-bolt filtering, part links, and torque tools…