2023 Mitsubishi Triton Bolt Sizes & Torque Specs
Free OEM-referenced torque and bolt specs for the 2023 Mitsubishi Triton.
This page is the OEM-referenced fastener summary for the 2023 Mitsubishi Triton. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.
For the 2023 Mitsubishi Triton, fasteners follow metric standards typical of late-model Mitsubishi engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).
Common fastener categories on the 2023 Mitsubishi Triton
- Wheel / lug nut torque and thread spec (covered above)
- Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
- Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
- Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
- Suspension control arm, sway bar, tie rod end and ball joint torque
- Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
- Differential cover bolts (RWD/4WD only) and transfer case fasteners
Repair guidance for this model year
For 2023 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.
Tools you will need
- Metric socket set (8mm-22mm), 6-point impact-rated
- Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
- Breaker bar (24" minimum) for initial loosening
- Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
- Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly
Frequently asked questions
What is the lug nut torque on a 2023 Mitsubishi Triton?
Manufacturer-specified torque values for the 2023 Mitsubishi Triton are in the factory service manual or owner's handbook. WhatSizeBolt sources values from manufacturer literature and verifies against community data — if we do not have this exact year listed, check the Mitsubishi brand page for the closest model year.
What socket size do I need for the 2023 Mitsubishi Triton lug nuts?
Most modern Mitsubishi vehicles use a 19mm or 21mm socket. Older Mitsubishi models from before 2000 may use a 13/16" SAE socket on certain trims. Confirm against the actual lug before purchasing aftermarket wheels.
Are the 2023 Mitsubishi Triton fasteners metric or SAE?
Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.
→ 2023 Mitsubishi Triton oil drain plug torque & size
All 5 2023 Mitsubishi Triton fastener specs
Per-bolt torque, wrench size, and thread spec for the 2023 Mitsubishi Triton, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. All 5 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data.
Wheels — 2023 Mitsubishi Triton
Wheel and lug nut spec for the 2023 Mitsubishi Triton. Wheel nut (alloy wheels) tightens to 128 Nm (94 ft-lb), takes a 21mm driver, runs on M12x1.5 threads, located at the all four wheels — alloy wheel spec. This figure is independently verified against OEM service data. The wheel nut (steel wheels) uses a 21mm drive on a M12x1.5 thread, torqued to 147 Nm (108 ft-lb) at the all four wheels — steel wheel spec. OEM-verified spec.
Brakes — 2023 Mitsubishi Triton
Brake fasteners on the 2023 Mitsubishi Triton — caliper bracket, slide pins, and banjo bolt torque follow. The front brake caliper bracket bolt uses a 19mm drive on a M12x1.25 thread, torqued to 113 Nm (83 ft-lb) at the front caliper bracket to knuckle, 2 bolts per side. OEM-verified spec.
Engine — 2023 Mitsubishi Triton
Engine bolt-by-bolt torque for the 2023 Mitsubishi Triton, including the long block, valve covers, and intake. At the bottom of oil pan — 4n15 diesel, the oil drain plug torques to 39 Nm (29 ft-lb) (17mm drive, M14x1.5 thread). Confirmed against manufacturer service literature.
Drivetrain — 2023 Mitsubishi Triton
Drivetrain and driveline fasteners for the 2023 Mitsubishi Triton — axle, transmission, and differential plugs. For the centre of front hub, 4wd models, plan for a 30mm tool on a M28x1.5 stud; final torque is 200 Nm (148 ft-lb) (front axle / hub nut (4wd)). This figure is independently verified against OEM service data.
New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2023 Mitsubishi Triton numbers above.
Loading the interactive 2023 Mitsubishi Triton fastener lookup with per-bolt filtering, part links, and torque tools…