2019 Volkswagen Golf Lug Nut Torque & Bolt Specs

The 2019 Volkswagen Golf lug nut torque is 89 ft-lbs (120 Nm), tightened with a 17mm hex socket on M14x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 89 ft-lbs (120 Nm) · Socket size: 17mm hex · Thread: M14x1.5.

This page is the OEM-referenced fastener summary for the 2019 Volkswagen Golf. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 2019 Volkswagen Golf, fasteners follow metric standards typical of late-model Volkswagen engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 2019 Volkswagen Golf

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2019 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2019 Volkswagen Golf?

The OEM-specified lug-nut torque for the 2019 Volkswagen Golf is 89 ft-lbs (120 Nm), using a 17mm hex socket on M14x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2019 Volkswagen Golf lug nuts?

The 2019 Volkswagen Golf uses a 17mm hex socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2019 Volkswagen Golf fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Volkswagen Golf years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

All 11 2019 Volkswagen Golf fastener specs

Per-bolt torque, wrench size, and thread spec for the 2019 Volkswagen Golf, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 4 of the 11 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Brakes — 2019 Volkswagen Golf

Brake fasteners on the 2019 Volkswagen Golf — caliper bracket, slide pins, and banjo bolt torque follow. The front caliper guide pin, torqued to 22 ft-lbs (30 Nm) at the front. This figure is independently verified against OEM service data. At the front, the front caliper bracket bolt torques to 148 ft-lbs (200 Nm) + replace bolts. OEM-verified spec.

Engine — 2019 Volkswagen Golf

Engine bolt-by-bolt torque for the 2019 Volkswagen Golf, including the long block, valve covers, and intake. At the oil pan, the oil drain plug torques to 22 ft-lbs (30 Nm) (M14x1.5 thread). OEM-verified spec. For the cylinder head, plan for the right driver; final torque is 22 ft-lbs (30 Nm) (spark plug). Confirmed against manufacturer service literature.

Suspension - Front — 2019 Volkswagen Golf

Suspension - Front fasteners on the 2019 Volkswagen Golf. For the suspension - front, plan for a 17mm tool on a M10 or M12 stud; final torque is 40 Nm + 45° (ball joint to control arm).

Transmission — 2019 Volkswagen Golf

Transmission fasteners on the 2019 Volkswagen Golf. Dsg drain plug tightens to 45 Nm (33 ft-lbs), takes a 22mm driver, runs on M14 threads, located at the transmission. The dsg mechatronic uses a 10mm drive on a M6 or M8 thread, torqued to 5 Nm + 90° at the transmission. At the transmission, the transmission fluid pump cover torques to 8 Nm (6 ft-lbs) (10mm drive, M6 thread).

Wheel — 2019 Volkswagen Golf

Wheel fasteners on the 2019 Volkswagen Golf. The lug bolt uses a 17mm hex drive on a M14x1.5 thread, torqued to 89 ft-lbs (120 Nm) at the wheel.

Engine - Mounts — 2019 Volkswagen Golf

Engine - Mounts fasteners on the 2019 Volkswagen Golf. At the engine - mounts, the transmission mount to transmission torques to 60 Nm + 90° (19mm drive, M12 thread). For the engine - mounts, plan for a 22mm tool on a M14 x 1.5 x 50mm stud; final torque is 130 Nm (96 ft-lbs) (dogbone/pendulum mount).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2019 Volkswagen Golf numbers above.

Loading the interactive 2019 Volkswagen Golf fastener lookup with per-bolt filtering, part links, and torque tools…