2020 Volkswagen Passat Lug Nut Torque & Bolt Specs

The 2020 Volkswagen Passat lug nut torque is 89 ft-lbs (120 Nm), tightened with a 17mm hex socket on M14x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 89 ft-lbs (120 Nm) · Socket size: 17mm hex · Thread: M14x1.5.

This page is the OEM-referenced fastener summary for the 2020 Volkswagen Passat. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 2020 Volkswagen Passat, fasteners follow metric standards typical of late-model Volkswagen engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 2020 Volkswagen Passat

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2020 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2020 Volkswagen Passat?

The OEM-specified lug-nut torque for the 2020 Volkswagen Passat is 89 ft-lbs (120 Nm), using a 17mm hex socket on M14x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2020 Volkswagen Passat lug nuts?

The 2020 Volkswagen Passat uses a 17mm hex socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2020 Volkswagen Passat fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Volkswagen Passat years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2020 Volkswagen Passat oil drain plug torque & size

All 7 2020 Volkswagen Passat fastener specs

Per-bolt torque, wrench size, and thread spec for the 2020 Volkswagen Passat, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Brakes — 2020 Volkswagen Passat

Brake fasteners on the 2020 Volkswagen Passat — caliper bracket, slide pins, and banjo bolt torque follow. The front brake caliper guide pin uses a 7mm Allen drive, torqued to 22 ft-lbs at the front brakes. At the front brakes, the front brake caliper carrier bolt torques to 148 ft-lbs (21mm drive, M12 thread). For the rear brakes, plan for a 13mm tool on a M8 stud; final torque is 26 ft-lbs (rear brake caliper guide pin bolt).

Engine — 2020 Volkswagen Passat

Engine bolt-by-bolt torque for the 2020 Volkswagen Passat, including the long block, valve covers, and intake. At the engine, the oil drain plug torques to 22 ft-lbs (30 Nm) (19mm hex drive, M14x1.5 thread). For the engine, plan for a 32mm cap tool; final torque is 15 ft-lbs (oil filter housing cap). Spark plug tightens to 22 ft-lbs, takes a 16mm driver, runs on M14 (14mm) threads, located at the engine.

Wheel — 2020 Volkswagen Passat

Wheel fasteners on the 2020 Volkswagen Passat. For the wheel, plan for a 17mm hex tool on a M14x1.5 stud; final torque is 89 ft-lbs (120 Nm) (lug bolt).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2020 Volkswagen Passat numbers above.

Loading the interactive 2020 Volkswagen Passat fastener lookup with per-bolt filtering, part links, and torque tools…