2022 Volkswagen Tiguan Lug Nut Torque & Bolt Specs

The 2022 Volkswagen Tiguan lug nut torque is 89 ft-lbs (120 Nm), tightened with a 17mm hex socket on M14x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 89 ft-lbs (120 Nm) · Socket size: 17mm hex · Thread: M14x1.5.

This page is the OEM-referenced fastener summary for the 2022 Volkswagen Tiguan. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 2022 Volkswagen Tiguan, fasteners follow metric standards typical of late-model Volkswagen engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 2022 Volkswagen Tiguan

Repair guidance for this model year

For 2022 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Frequently asked questions

What is the lug nut torque on a 2022 Volkswagen Tiguan?

The OEM-specified lug-nut torque for the 2022 Volkswagen Tiguan is 89 ft-lbs (120 Nm), using a 17mm hex socket on M14x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2022 Volkswagen Tiguan lug nuts?

The 2022 Volkswagen Tiguan uses a 17mm hex socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2022 Volkswagen Tiguan fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Volkswagen Tiguan years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2022 Volkswagen Tiguan oil drain plug torque & size

→ 2022 Volkswagen Tiguan engine & transmission mount torque specs

All 12 2022 Volkswagen Tiguan fastener specs

Per-bolt torque, wrench size, and thread spec for the 2022 Volkswagen Tiguan, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 2 of the 12 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Brakes — 2022 Volkswagen Tiguan

Brake fasteners on the 2022 Volkswagen Tiguan — caliper bracket, slide pins, and banjo bolt torque follow. For the front brake caliper bracket to steering knuckle, plan for a 21mm tool on a M12 stud; final torque is 148 ft-lbs (200 Nm) (front caliper bracket bolt). Front caliper guide pin tightens to 22 ft-lbs (30 Nm), located at the front. This figure is independently verified against OEM service data.

Engine — 2022 Volkswagen Tiguan

Engine bolt-by-bolt torque for the 2022 Volkswagen Tiguan, including the long block, valve covers, and intake. Oil drain plug tightens to 22 ft-lbs (30 Nm), takes a 19mm hex driver, runs on M14x1.5 threads, located at the engine. The spark plug, torqued to 22 ft-lbs (30 Nm) at the cylinder head. OEM-verified spec.

Transmission — 2022 Volkswagen Tiguan

Transmission fasteners on the 2022 Volkswagen Tiguan. The dsg drain plug uses a 22mm drive on a M14 thread, torqued to 45 Nm (33 ft-lbs) at the transmission. At the transmission, the dsg mechatronic torques to 5 Nm + 90° (10mm drive, M6 or M8 thread). For the transmission, plan for a 10mm tool on a M6 stud; final torque is 8 Nm (6 ft-lbs) (transmission fluid pump cover).

Engine - Mounts — 2022 Volkswagen Tiguan

Engine - Mounts fasteners on the 2022 Volkswagen Tiguan. At the engine - mounts, the transmission mount to transmission torques to 60 Nm + 90° (19mm drive, M12 thread). For the engine - mounts, plan for a 19mm tool on a M12 stud; final torque is 50 Nm + 90° (transmission mount to frame). Dogbone/pendulum mount tightens to 130 Nm (96 ft-lbs), takes a 22mm driver, runs on M14 x 1.5 x 50mm threads, located at the engine - mounts.

Suspension - Front — 2022 Volkswagen Tiguan

Suspension - Front fasteners on the 2022 Volkswagen Tiguan. For the suspension - front, plan for a 17mm tool on a M10 or M12 stud; final torque is 40 Nm + 45° (ball joint to control arm).

Wheel Hardware — 2022 Volkswagen Tiguan

Wheel Hardware fasteners on the 2022 Volkswagen Tiguan. Wheel bolt (lug bolt) tightens to 89 ft-lbs (120 Nm), takes a 17mm hex driver, runs on M14x1.5 threads, located at the all four wheels.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2022 Volkswagen Tiguan numbers above.

Loading the interactive 2022 Volkswagen Tiguan fastener lookup with per-bolt filtering, part links, and torque tools…