2014 Toyota RAV4 Brake Job Torque Specs

OEM-referenced torque, socket, and thread specs for the 12 brake fasteners you touch on a 2014 Toyota RAV4 brake job — caliper mounting bolts, caliper bracket bolts, slide/guide pins, and rotor hardware, including the Rear Brake Caliper Mounting (Bracket to Carrier) Bolt (torques to 88 Nm (65 ft-lbs), 17mm socket, M12x1.25 thread). Every value is safety-critical; verify against your service manual and use a calibrated torque wrench. Full bolt specs for the rest of the vehicle are linked below.

Caliper Bracket Bolts torque — 2014 Toyota RAV4

On the 2014 Toyota RAV4, the caliper bracket bolts are: Rear Brake Caliper Mounting (Bracket to Carrier) Bolt (torques to 88 Nm (65 ft-lbs), 17mm socket, M12x1.25 thread); Front Brake Caliper Mounting (Bracket to Knuckle) Bolt (torques to 72 ft-lbs (98 Nm), 17mm socket, M12x1.25 thread); Parking Brake Cable Bracket Bolt (torques to 72 ft-lbs (98 Nm), 10mm socket, M6x1.0 thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

Caliper Slide / Guide Pins torque — 2014 Toyota RAV4

On the 2014 Toyota RAV4, the caliper slide / guide pins are: Rear Brake Caliper Guide Pin Bolt (torques to 27 Nm (20 ft-lbs), 12mm socket, M10x1.25 thread); Front Brake Caliper Guide Pin Bolt (torques to 20 ft-lbs (27 Nm), 12mm socket, M10x1.25 thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

Hydraulic (Banjo & Bleeder) torque — 2014 Toyota RAV4

On the 2014 Toyota RAV4, the hydraulic (banjo & bleeder) are: Front Brake Flexible Hose Banjo Bolt (torques to 29 Nm (22 ft-lbs), 14mm socket, M10x1.25 thread); Brake Hose Clamp Bolt (torques to 19 Nm (14 ft-lbs), 12mm socket, M8x1.25 thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

Parking-Brake Hardware torque — 2014 Toyota RAV4

On the 2014 Toyota RAV4, the parking-brake hardware are: Parking Brake Cable to Rear Brake Caliper Bolt (torques to 88 Nm (65 ft-lbs), 17mm socket, M10x1.25 thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

Other Brake Fasteners torque — 2014 Toyota RAV4

On the 2014 Toyota RAV4, the other brake fasteners are: ABS Speed Sensor Bolt (Rear) (torques to 8.5 Nm (75 in-lbs), 10mm socket, M6x1.0 thread); Brake Tube Flare Nut (torques to 15 Nm (11 ft-lbs), 10mm Flare Nut Wrench socket, M10x1.0 thread); Brake Master Cylinder Mounting Nut (torques to 72 ft-lbs (98 Nm), 14mm socket, M10x1.25 thread); ABS Speed Sensor Bolt (Front) (torques to 8.5 Nm (75 in-lbs), 10mm socket, M6x1.0 thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

How to do a RAV4 brake job right

Work one corner at a time so the other side holds a reference. Unbolt the caliper, hang it from the coil with wire (never let it dangle on the hose), and back the caliper bracket bolts out — those are the high-torque fasteners (commonly 80-140 ft-lbs) and are frequently torque-to-yield, so plan to replace them. Clean and lube the slide pins, or replace the pin boots if torn. Apply the specified thread-locker, start every bolt by hand to avoid cross-threading, and make the final pass with a calibrated torque wrench. Pump the pedal to seat the pads before you drive, and re-torque the lug nuts after the wheels go back on.

Tools you need for a RAV4 brake job

The 2014 Toyota RAV4 brake job calls for 17mm, 14mm, 10mm, 10mm Flare Nut Wrench, 12mm sockets, a caliper slide-pin tool or hex/Torx bit set, a torque wrench that covers the high bracket-bolt values, thread-locker, and brake grease for the slide pins. A caliper piston compressor makes seating the new pads far easier. See the recommended tools and replacement hardware linked below.

Related lookups

Loading interactive lookup…