2020 Toyota RAV4 Brake Job Torque Specs

OEM-referenced torque, socket, and thread specs for the 12 brake fasteners you touch on a 2020 Toyota RAV4 brake job — caliper mounting bolts, caliper bracket bolts, slide/guide pins, and rotor hardware, including the Front Brake Caliper Bracket Bolts (Aluminum Knuckle) (torques to 79 ft-lbs (107 Nm) steel knuckle / 111 ft-lbs (150 Nm) aluminum knuckle, 17mm socket, M12x1.25 thread). Every value is safety-critical; verify against your service manual and use a calibrated torque wrench. Full bolt specs for the rest of the vehicle are linked below.

Caliper Mounting Bolts torque — 2020 Toyota RAV4

On the 2020 Toyota RAV4, the caliper mounting bolts are: Rear Brake Caliper Assembly Bolts (to Axle Carrier) (torques to 107 Nm (79 ft-lbs), 17mm socket, M12x1.25 thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

Caliper Bracket Bolts torque — 2020 Toyota RAV4

On the 2020 Toyota RAV4, the caliper bracket bolts are: Rear Brake Caliper Bracket Bolts (17mm socket, M12x1.25 thread); Front Brake Caliper Bracket Bolts (Aluminum Knuckle) (torques to 79 ft-lbs (107 Nm) steel knuckle / 111 ft-lbs (150 Nm) aluminum knuckle, 17mm socket, M12x1.25 thread); Front Brake Caliper Bracket Bolts (to Steering Knuckle) (torques to 79 ft-lbs (107 Nm) steel knuckle / 111 ft-lbs (150 Nm) aluminum knuckle, 17mm socket, M12x1.25 thread); Front ABS Speed Sensor / Brake Hose Bracket Bolt (to Strut) (torques to 29 Nm (21 ft-lbs), 12mm socket, M8x1.25 thread); Rear Flexible Hose Bracket Bolt (to Axle Carrier) (torques to 29 Nm (21 ft-lbs), 12mm socket, M8x1.25 thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

Caliper Slide / Guide Pins torque — 2020 Toyota RAV4

On the 2020 Toyota RAV4, the caliper slide / guide pins are: Rear Brake Caliper Guide Pin Bolts (torques to 27 Nm (20 ft-lbs), 14mm (hold pin with hex) socket, M10x1.25 thread); Front Brake Caliper Guide Pin Bolts (torques to 25 ft-lbs (34 Nm), 14mm (hold pin with 6mm hex) socket, M10x1.25 thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

Hydraulic (Banjo & Bleeder) torque — 2020 Toyota RAV4

On the 2020 Toyota RAV4, the hydraulic (banjo & bleeder) are: Brake Flexible Hose to Caliper Banjo Bolt (Front) (torques to 29 Nm (21 ft-lbs), 17mm socket, M10x1.25 banjo thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

Parking-Brake Hardware torque — 2020 Toyota RAV4

On the 2020 Toyota RAV4, the parking-brake hardware are: Rear No. 2 Parking Brake Wire Nut (to Trailing Arm) (torques to 15.5 Nm (11 ft-lbs), 12mm socket, M8x1.25 thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

Other Brake Fasteners torque — 2020 Toyota RAV4

On the 2020 Toyota RAV4, the other brake fasteners are: Rear ABS Speed Sensor Bolt (to Rear Axle Carrier) (torques to 8.5 Nm (75 in-lbs), 10mm socket, M6x1.0 thread); Front ABS Speed Sensor Bolt (to Steering Knuckle) (torques to 8.5 Nm (75 in-lbs), 10mm socket, M6x1.0 thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

How to do a RAV4 brake job right

Work one corner at a time so the other side holds a reference. Unbolt the caliper, hang it from the coil with wire (never let it dangle on the hose), and back the caliper bracket bolts out — those are the high-torque fasteners (commonly 80-140 ft-lbs) and are frequently torque-to-yield, so plan to replace them. Clean and lube the slide pins, or replace the pin boots if torn. Apply the specified thread-locker, start every bolt by hand to avoid cross-threading, and make the final pass with a calibrated torque wrench. Pump the pedal to seat the pads before you drive, and re-torque the lug nuts after the wheels go back on.

Tools you need for a RAV4 brake job

The 2020 Toyota RAV4 brake job calls for 17mm, 14mm (hold pin with hex), 14mm (hold pin with 6mm hex), 10mm, 12mm sockets, a caliper slide-pin tool or hex/Torx bit set, a torque wrench that covers the high bracket-bolt values, thread-locker, and brake grease for the slide pins. A caliper piston compressor makes seating the new pads far easier. See the recommended tools and replacement hardware linked below.

Related lookups

Loading interactive lookup…