2023 Nissan Pathfinder Brake Job Torque Specs

OEM-referenced torque, socket, and thread specs for the 7 brake fasteners you touch on a 2023 Nissan Pathfinder brake job — caliper mounting bolts, caliper bracket bolts, slide/guide pins, and rotor hardware, including the Rear Caliper Bracket Bolt (torques to 65 ft-lb (88 Nm), 21mm socket, M14x1.5 thread). Every value is safety-critical; verify against your service manual and use a calibrated torque wrench. Full bolt specs for the rest of the vehicle are linked below.

Caliper Mounting Bolts torque — 2023 Nissan Pathfinder

On the 2023 Nissan Pathfinder, the caliper mounting bolts are: Rear Brake Caliper Bolt (torques to 34 ft-lb (46 Nm), 14mm socket, M10x1.25 thread); Front Brake Caliper Bolt (torques to 34 ft-lb (46 Nm), 17mm socket, M12x1.25 thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

Caliper Bracket Bolts torque — 2023 Nissan Pathfinder

On the 2023 Nissan Pathfinder, the caliper bracket bolts are: Rear Caliper Bracket Bolt (torques to 65 ft-lb (88 Nm), 21mm socket, M14x1.5 thread); Front Caliper Bracket Bolt (torques to 107 ft-lb (145 Nm), 22mm socket, M14x1.5 thread); Front Brake Caliper Bracket Bolt (torques to 133 ft-lbs (180 Nm)). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

Caliper Slide / Guide Pins torque — 2023 Nissan Pathfinder

On the 2023 Nissan Pathfinder, the caliper slide / guide pins are: Front Brake Caliper Guide Pin Bolt (torques to 34 ft-lbs (46 Nm)). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

Hydraulic (Banjo & Bleeder) torque — 2023 Nissan Pathfinder

On the 2023 Nissan Pathfinder, the hydraulic (banjo & bleeder) are: Brake Bleeder Screw (torques to 11 ft-lb (15 Nm), 8mm socket). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

How to do a Pathfinder brake job right

Work one corner at a time so the other side holds a reference. Unbolt the caliper, hang it from the coil with wire (never let it dangle on the hose), and back the caliper bracket bolts out — those are the high-torque fasteners (commonly 80-140 ft-lbs) and are frequently torque-to-yield, so plan to replace them. Clean and lube the slide pins, or replace the pin boots if torn. Apply the specified thread-locker, start every bolt by hand to avoid cross-threading, and make the final pass with a calibrated torque wrench. Pump the pedal to seat the pads before you drive, and re-torque the lug nuts after the wheels go back on.

Tools you need for a Pathfinder brake job

The 2023 Nissan Pathfinder brake job calls for 8mm, 21mm, 14mm, 22mm, 17mm sockets, a caliper slide-pin tool or hex/Torx bit set, a torque wrench that covers the high bracket-bolt values, thread-locker, and brake grease for the slide pins. A caliper piston compressor makes seating the new pads far easier. See the recommended tools and replacement hardware linked below.

Related lookups

Loading interactive lookup…