2025 Ford Escape Brake Job Torque Specs

OEM-referenced torque, socket, and thread specs for the 7 brake fasteners you touch on a 2025 Ford Escape brake job — caliper mounting bolts, caliper bracket bolts, slide/guide pins, and rotor hardware, including the Front Caliper Bracket Bolts (All) (torques to 81 ft-lbs (110 Nm), 18mm socket, M12x1.5 thread). Every value is safety-critical; verify against your service manual and use a calibrated torque wrench. Full bolt specs for the rest of the vehicle are linked below.

Caliper Mounting Bolts torque — 2025 Ford Escape

On the 2025 Ford Escape, the caliper mounting bolts are: Brake Caliper Bolt (torques to 22-25 ft-lbs, 13mm socket, M8x1.25 thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

Caliper Bracket Bolts torque — 2025 Ford Escape

On the 2025 Ford Escape, the caliper bracket bolts are: Front Caliper Bracket Bolts (All) (torques to 81 ft-lbs (110 Nm), 18mm socket, M12x1.5 thread); Rear Caliper Bracket Bolts (All) (torques to 46 ft-lbs (63 Nm), 13mm socket, M10 thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

Caliper Slide / Guide Pins torque — 2025 Ford Escape

On the 2025 Ford Escape, the caliper slide / guide pins are: Front Caliper Slide Pin Bolts (All) (torques to 21 ft-lbs (28 Nm), 7mm hex socket, M8 thread); Rear Caliper Slide Pin Bolts (All) (torques to 21 ft-lbs (28 Nm), 7mm hex socket, M8 thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

Rotor Retaining Hardware torque — 2025 Ford Escape

On the 2025 Ford Escape, the rotor retaining hardware are: Rotor Retaining Screw (All) (torques to 10-15 in-lbs (1-2 Nm), T20 Torx socket, M5 thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

Parking-Brake Hardware torque — 2025 Ford Escape

On the 2025 Ford Escape, the parking-brake hardware are: Rear Caliper Bolt (EPB / electric parking brake) (All) (torques to 25 ft-lbs (34 Nm), T45 Torx socket, M8 thread). Brake hardware is safety-critical — caliper slide pins and bracket bolts almost always take fresh thread-locker, single-use torque-to-yield bolts must be replaced, and every value should be set with a calibrated torque wrench, not an impact gun.

How to do a Escape brake job right

Work one corner at a time so the other side holds a reference. Unbolt the caliper, hang it from the coil with wire (never let it dangle on the hose), and back the caliper bracket bolts out — those are the high-torque fasteners (commonly 80-140 ft-lbs) and are frequently torque-to-yield, so plan to replace them. Clean and lube the slide pins, or replace the pin boots if torn. Apply the specified thread-locker, start every bolt by hand to avoid cross-threading, and make the final pass with a calibrated torque wrench. Pump the pedal to seat the pads before you drive, and re-torque the lug nuts after the wheels go back on.

Tools you need for a Escape brake job

The 2025 Ford Escape brake job calls for 18mm, 13mm, 7mm hex, T45 Torx, T20 Torx sockets, a caliper slide-pin tool or hex/Torx bit set, a torque wrench that covers the high bracket-bolt values, thread-locker, and brake grease for the slide pins. A caliper piston compressor makes seating the new pads far easier. See the recommended tools and replacement hardware linked below.

Related lookups

Loading interactive lookup…