2000 Dodge Ram 2500 Suspension & Steering Torque Specs

OEM-referenced torque, socket, and thread specs for the 8 front and rear suspension and steering fasteners on the 2000 Dodge Ram 2500 — including the Lower Control Arm Bolt (torques to 130 lb-ft, 21mm socket, M14x1.5 thread). Every value is safety-critical; verify against your service manual and use a calibrated torque wrench. Full bolt specs for the rest of the vehicle are linked below.

Control Arms & Ball Joints torque — 2000 Dodge Ram 2500

On the 2000 Dodge Ram 2500, the control arms & ball joints fasteners are: Lower Control Arm Bolt (torques to 130 lb-ft, 21mm socket, M14x1.5 thread); Upper Control Arm Bolt (torques to 100 lb-ft, 18mm socket, M12x1.75 thread). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Struts, Shocks & Springs torque — 2000 Dodge Ram 2500

On the 2000 Dodge Ram 2500, the struts, shocks & springs fasteners are: Rear Leaf Spring U-Bolt Nut (torques to 135-175 ft-lbs, 22mm socket, M14x2.0 thread); Shock Absorber Bottom Bolt (torques to 100 lb-ft, 18mm socket, M12x1.75 thread); Shock Absorber Top Nut (torques to 25 lb-ft, 18mm socket, M12x1.75 thread). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Sway Bar & Stabilizer Links torque — 2000 Dodge Ram 2500

On the 2000 Dodge Ram 2500, the sway bar & stabilizer links fasteners are: Sway Bar Link Nut (torques to 75 lb-ft, 15mm socket, M10x1.5 thread). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Steering (Tie Rods & Linkage) torque — 2000 Dodge Ram 2500

On the 2000 Dodge Ram 2500, the steering (tie rods & linkage) fasteners are: Tie Rod End Nut (torques to 60-75 ft-lbs, 22mm socket, M14x1.5 thread). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Other Suspension Fasteners torque — 2000 Dodge Ram 2500

On the 2000 Dodge Ram 2500, the other suspension fasteners fasteners are: Transmission Crossmember Bolt (torques to 70 lb-ft, 18mm socket, M12x1.75 thread). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

How to torque Ram 2500 suspension & steering fasteners

Torque suspension and steering fasteners with the vehicle at ride height (wheels loaded) wherever a bushing is involved — tightening a control-arm or sway-bar bushing bolt with the suspension hanging pre-loads the rubber and it fails early. Clean the threads, start every fastener by hand to avoid cross-threading, and make the final pass with a calibrated torque wrench rather than an impact gun. Ball-joint and tie-rod castle nuts take a new cotter pin; never back a castle nut off to line up the hole — only tighten to the next slot.

Related lookups

Loading interactive lookup…