2006 Toyota RAV4 Suspension & Steering Torque Specs

OEM-referenced torque, socket, and thread specs for the 45 front and rear suspension and steering fasteners on the 2006 Toyota RAV4 — including the Front Lower Ball Joint to Control Arm Bolt/Nut (torques to 92 Nm (68 ft-lbs), 17mm socket, M12x1.25 thread). Every value is safety-critical; verify against your service manual and use a calibrated torque wrench. Full bolt specs for the rest of the vehicle are linked below.

Control Arms & Ball Joints torque — 2006 Toyota RAV4

On the 2006 Toyota RAV4, the control arms & ball joints fasteners are: Front Lower Ball Joint to Control Arm Bolt/Nut (torques to 92 Nm (68 ft-lbs), 17mm socket, M12x1.25 thread); Front Lower Ball Joint Nut (Ball Joint to Knuckle) (torques to 133 Nm (98 ft-lbs), 22mm socket, M14x1.5 thread); Front Lower Control Arm to Crossmember Bolt (torques to 233 Nm (172 ft-lbs), 22mm socket, M16x1.5 thread); Rear Trailing Arm to Body Bolt (Rear End) (torques to 200 Nm (148 ft-lbs), 22mm socket, M16x1.5 thread); Rear Axle Carrier (Hub) to Trailing Arm (torques to 90 Nm (66 ft-lbs), 17mm socket, M12x1.25 thread); Front Axle Hub Nut (FWD/4WD — 26mm spindle) (torques to 216 Nm (159 ft-lbs), 30mm (12-point socket) socket, M24x1.5 thread); Rear Upper Control Arm Bolt (to Suspension Member) (torques to 90 Nm (66 ft-lbs), 17mm socket, M14x1.5 thread); Rear Trailing Arm to Body Bolt (Front End) (torques to 150 Nm (111 ft-lbs), 22mm socket, M16x1.5 thread). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Struts, Shocks & Springs torque — 2006 Toyota RAV4

On the 2006 Toyota RAV4, the struts, shocks & springs fasteners are: Rear Shock Absorber Lower Mount Bolt (torques to 80 Nm (59 ft-lbs), 17mm socket, M14x1.5 thread); Front Strut Upper Mount Nut (torques to 50 Nm (37 ft-lbs), 14mm socket, M10x1.25 thread); Front Strut Piston Rod Nut (torques to 47 Nm (35 ft-lbs), 19mm (hold rod with T55 or Allen) socket, M14x1.5 thread); Front Strut Lower Pinch Bolt/Nut (Strut to Knuckle) (torques to 240 Nm (177 ft-lbs), 22mm (both bolt head and nut) socket, M14x1.5 thread); Front Strut Top Mount Nut (torques to 50 Nm (37 ft-lbs), 17mm socket, M10x1.25 thread); Rear Shock Absorber to Suspension Member Bolt (torques to 80 Nm (59 ft-lbs), 17mm socket, M12x1.25 thread). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Sway Bar & Stabilizer Links torque — 2006 Toyota RAV4

On the 2006 Toyota RAV4, the sway bar & stabilizer links fasteners are: Rear Stabilizer Bar Bracket Bolt (torques to 60 Nm (44 ft-lbs), 14mm socket, M10x1.25 thread); Front Sway Bar Link Nut (Strut to Link) (torques to 74 Nm (55 ft-lbs), 17mm (hold stud with 6mm Hex) socket, M14x1.5 thread); Rear Sway Bar Link to No. 2 Arm Nut (torques to 30 Nm (22 ft-lbs), 14mm (hold stud with 6mm Hex) socket, M12x1.25 thread); Rear Sway Bar Bracket Bolt (torques to 60 Nm (44 ft-lbs), 14mm socket, M10x1.25 thread); Front Sway Bar Bracket Bolt (torques to 25 Nm (18 ft-lbs), 12mm socket, M8x1.25 thread); Front Sway Bar End Link Nut (torques to 74 Nm (55 ft-lbs), 17mm / 5mm Allen (hold stud) socket, M12x1.25 thread); Rear Sway Bar End Link Nut (torques to 74 Nm (55 ft-lbs), 17mm / 5mm Allen socket, M12x1.25 thread). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Steering (Tie Rods & Linkage) torque — 2006 Toyota RAV4

On the 2006 Toyota RAV4, the steering (tie rods & linkage) fasteners are: Power Steering Rack Mount Bolt (torques to 138 Nm (102 ft-lbs), 19mm socket, M14x1.5 thread); Steering Knuckle to Front Hub Bearing Bolt (torques to 96 Nm (71 ft-lbs), 17mm socket, M12x1.25 thread); Steering Intermediate Shaft U-Joint Pinch Bolt (torques to 35 Nm (26 ft-lbs), 14mm socket, M12x1.25 thread); Tie Rod End Nut (Outer) (torques to 49 Nm (36 ft-lbs), 22mm socket, M14x1.5 thread); Tie Rod End Locknut (Inner to Outer Adjuster) (torques to 88 Nm (65 ft-lbs), 21mm / 22mm Combo Wrench socket, M14x1.5 thread); Steering Wheel Nut (torques to 50 Nm (37 ft-lbs), 22mm socket, M18x1.5 thread); Outer Tie Rod End Nut (torques to 49 Nm (36 ft-lbs), 19mm socket, M12x1.25 thread); Inner Tie Rod (Rack End) to Rack (torques to 60 Nm (44 ft-lbs), Special tool (crowfoot or inner tie rod tool) socket, M14x1.5 thread). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Wheel Hub & Bearing torque — 2006 Toyota RAV4

On the 2006 Toyota RAV4, the wheel hub & bearing fasteners are: Rear Axle Hub Bearing Bolt (to Carrier) (torques to 90 Nm (66 ft-lbs), 17mm socket, M12x1.25 thread). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Other Suspension Fasteners torque — 2006 Toyota RAV4

On the 2006 Toyota RAV4, the other suspension fasteners fasteners are: Rear Engine Mount (Insulator RR) to Crossmember (torques to 95 Nm (70 ft-lbs), 19mm socket, M14x1.5 thread); Wheel Lug Nut (torques to 103 Nm (76 ft-lbs), 21mm socket, M12x1.5 thread); Rear Suspension No. 2 Arm to Suspension Member Bolt (torques to 90 Nm (66 ft-lbs), 19mm socket, M14x1.5 thread); Rear Suspension No. 1 Arm to Axle Carrier Bolt (torques to 100 Nm (74 ft-lbs), 19mm socket, M14x1.5 thread); Engine Front Mount (Insulator FR) to Crossmember Bolt (torques to 95 Nm (70 ft-lbs), 19mm socket, M14x1.5 thread); Front Subframe (Crossmember) Bolt to Body (torques to 145 Nm (107 ft-lbs), 22mm socket, M14x1.5 thread). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

How to torque RAV4 suspension & steering fasteners

Torque suspension and steering fasteners with the vehicle at ride height (wheels loaded) wherever a bushing is involved — tightening a control-arm or sway-bar bushing bolt with the suspension hanging pre-loads the rubber and it fails early. Clean the threads, start every fastener by hand to avoid cross-threading, and make the final pass with a calibrated torque wrench rather than an impact gun. Ball-joint and tie-rod castle nuts take a new cotter pin; never back a castle nut off to line up the hole — only tighten to the next slot.

Related lookups

Loading interactive lookup…