2022 Acura Ilx Lug Nut Torque & Bolt Specs

The 2022 Acura Ilx lug nut torque is 80 ft-lbs (108 Nm), tightened with a 19mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 19mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2022 Acura Ilx. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Honda's lug-nut torque sits at 80 ft-lbs (108 Nm) for nearly every passenger model from 1998 onward, with an M12x1.5 thread on most cars and the larger 14mm thread on Ridgeline and Pilot. The 19mm socket Honda uses is one of the only OEM oddities in the Japanese lineup — bring a 19mm with you, not just a 21mm. Honda factory torque values for engine oil drain plugs are unusually low (29 ft-lbs on most engines) and the crush washer is single-use, so replace it every oil change.

Common fastener categories on the 2022 Acura Ilx

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2022 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2022 Acura Ilx?

The OEM-specified lug-nut torque for the 2022 Acura Ilx is 80 ft-lbs (108 Nm), using a 19mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2022 Acura Ilx lug nuts?

The 2022 Acura Ilx uses a 19mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2022 Acura Ilx fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Acura Ilx years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2022 Acura Ilx oil drain plug torque & size

→ 2022 Acura Ilx suspension & steering torque specs (control arm, ball joint, tie rod)

All 12 2022 Acura Ilx fastener specs

Per-bolt torque, wrench size, and thread spec for the 2022 Acura Ilx, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Brakes — 2022 Acura Ilx

Brake fasteners on the 2022 Acura Ilx — caliper bracket, slide pins, and banjo bolt torque follow. The rear caliper slide pin uses a 12mm drive on a M8x1.25 thread, torqued to 16 ft-lbs (22 Nm) at the rear. At the front, the front caliper bracket bolt torques to 80 ft-lbs (108 Nm) (17mm drive, M12x1.25 thread). For the rear, plan for a 14mm tool on a M10x1.25 stud; final torque is 41 ft-lbs (55 Nm) (rear caliper bracket bolt). Front caliper slide pin tightens to 18 ft-lbs (25 Nm), takes a 13mm driver, runs on M8x1.25 threads, located at the front.

Engine — 2022 Acura Ilx

Engine bolt-by-bolt torque for the 2022 Acura Ilx, including the long block, valve covers, and intake. The oil drain plug torques to 29 ft-lbs (39 Nm) (17mm drive, M14x1.5 thread). plan for a 64mm cap tool; final torque is Hand tight + 3/4 turn (oil filter). Spark plug tightens to 13 ft-lbs (18 Nm), takes a 5/8 in. driver, runs on M14x1.25 threads.

Suspension — 2022 Acura Ilx

Suspension and chassis fastener torque for the 2022 Acura Ilx — strut, control arm, and sway bar values. For the front, plan for a 17mm tool on a M12x1.25 stud; final torque is 33 ft-lbs (45 Nm) (front strut top nut). Front lower control arm bolt tightens to 51 ft-lbs (69 Nm), takes a 17mm driver, runs on M12x1.25 threads, located at the front. The rear lower control arm bolt uses a 17mm drive on a M12x1.25 thread, torqued to 43 ft-lbs (59 Nm) at the rear.

Transmission — 2022 Acura Ilx

Transmission fasteners on the 2022 Acura Ilx. Transmission drain plug tightens to 35 ft-lbs (47 Nm), takes a 17mm driver, runs on M18x1.5 threads.

Wheels & Tires — 2022 Acura Ilx

Wheels & Tires fasteners on the 2022 Acura Ilx. The lug nut uses a 19mm drive on a M12x1.5 thread, torqued to 80 ft-lbs (108 Nm).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2022 Acura Ilx numbers above.

Loading the interactive 2022 Acura Ilx fastener lookup with per-bolt filtering, part links, and torque tools…