2014 Bobcat E35 Bolt Sizes & Torque Specs

Free OEM-referenced torque and bolt specs for the 2014 Bobcat E35.

This page is the OEM-referenced fastener summary for the 2014 Bobcat E35. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 2014 Bobcat E35, fasteners follow metric standards typical of late-model Bobcat engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 2014 Bobcat E35

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2014 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2014 Bobcat E35?

Manufacturer-specified torque values for the 2014 Bobcat E35 are in the factory service manual or owner's handbook. WhatSizeBolt sources values from manufacturer literature and verifies against community data — if we do not have this exact year listed, check the Bobcat brand page for the closest model year.

What socket size do I need for the 2014 Bobcat E35 lug nuts?

Most modern Bobcat vehicles use a 19mm or 21mm socket. Older Bobcat models from before 2000 may use a 13/16" SAE socket on certain trims. Confirm against the actual lug before purchasing aftermarket wheels.

Are the 2014 Bobcat E35 fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Bobcat E35 years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2014 Bobcat E35 oil drain plug torque & size

All 6 2014 Bobcat E35 fastener specs

Per-bolt torque, wrench size, and thread spec for the 2014 Bobcat E35, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Engine — 2014 Bobcat E35

Engine bolt-by-bolt torque for the 2014 Bobcat E35, including the long block, valve covers, and intake. For the engine oil sump, plan for a 17mm tool on a M14x1.5 stud; final torque is 22–25 ft-lbs (30–34 Nm) (engine oil drain plug (kubota d1703)).

Drivetrain — 2014 Bobcat E35

Drivetrain and driveline fasteners for the 2014 Bobcat E35 — axle, transmission, and differential plugs. Final drive drain plug tightens to 29–36 ft-lbs (40–49 Nm), takes a 22mm driver, runs on M16x1.5 threads, located at the final drive gear box (one per side).

Attachment — 2014 Bobcat E35

Attachment fasteners on the 2014 Bobcat E35. The bucket pin retaining bolt uses a 18mm drive on a M12x1.75 thread, torqued to 75 ft-lbs (102 Nm) at the bucket pin lock bolt.

Safety — 2014 Bobcat E35

Safety fasteners on the 2014 Bobcat E35. At the rops to upper frame (4 bolts), the rops mounting bolt torques to 155 ft-lbs (210 Nm) (24mm drive, M16x2.0 thread).

Undercarriage — 2014 Bobcat E35

Undercarriage fasteners on the 2014 Bobcat E35. For the swing bearing ring, plan for a 24mm tool on a M16x2.0 stud; final torque is 155 ft-lbs (210 Nm) (swing bearing bolt). Track shoe bolt tightens to 130–155 ft-lbs (177–210 Nm), takes a 24mm driver, runs on M16x1.5 threads, located at the track shoes — 3 bolts per shoe, both sides.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2014 Bobcat E35 numbers above.

Loading the interactive 2014 Bobcat E35 fastener lookup with per-bolt filtering, part links, and torque tools…