2022 Bobcat E35 Bolt Sizes & Torque Specs

Free OEM-referenced torque and bolt specs for the 2022 Bobcat E35.

This page is the OEM-referenced fastener summary for the 2022 Bobcat E35. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 2022 Bobcat E35, fasteners follow metric standards typical of late-model Bobcat engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 2022 Bobcat E35

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2022 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2022 Bobcat E35?

Manufacturer-specified torque values for the 2022 Bobcat E35 are in the factory service manual or owner's handbook. WhatSizeBolt sources values from manufacturer literature and verifies against community data — if we do not have this exact year listed, check the Bobcat brand page for the closest model year.

What socket size do I need for the 2022 Bobcat E35 lug nuts?

Most modern Bobcat vehicles use a 19mm or 21mm socket. Older Bobcat models from before 2000 may use a 13/16" SAE socket on certain trims. Confirm against the actual lug before purchasing aftermarket wheels.

Are the 2022 Bobcat E35 fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Bobcat E35 years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2022 Bobcat E35 oil drain plug torque & size

All 6 2022 Bobcat E35 fastener specs

Per-bolt torque, wrench size, and thread spec for the 2022 Bobcat E35, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Engine — 2022 Bobcat E35

Engine bolt-by-bolt torque for the 2022 Bobcat E35, including the long block, valve covers, and intake. Engine oil drain plug (kubota d1703) tightens to 22–25 ft-lbs (30–34 Nm), takes a 17mm driver, runs on M14x1.5 threads, located at the engine oil sump.

Drivetrain — 2022 Bobcat E35

Drivetrain and driveline fasteners for the 2022 Bobcat E35 — axle, transmission, and differential plugs. The final drive drain plug uses a 22mm drive on a M16x1.5 thread, torqued to 29–36 ft-lbs (40–49 Nm) at the final drive gear box (one per side).

Undercarriage — 2022 Bobcat E35

Undercarriage fasteners on the 2022 Bobcat E35. At the track shoes — 3 bolts per shoe, both sides, the track shoe bolt torques to 130–155 ft-lbs (177–210 Nm) (24mm drive, M16x1.5 thread). For the swing bearing ring, plan for a 24mm tool on a M16x2.0 stud; final torque is 155 ft-lbs (210 Nm) (swing bearing bolt).

Safety — 2022 Bobcat E35

Safety fasteners on the 2022 Bobcat E35. For the rops to upper frame (4 bolts), plan for a 24mm tool on a M16x2.0 stud; final torque is 155 ft-lbs (210 Nm) (rops mounting bolt).

Attachment — 2022 Bobcat E35

Attachment fasteners on the 2022 Bobcat E35. Bucket pin retaining bolt tightens to 75 ft-lbs (102 Nm), takes a 18mm driver, runs on M12x1.75 threads, located at the bucket pin lock bolt.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2022 Bobcat E35 numbers above.

Loading the interactive 2022 Bobcat E35 fastener lookup with per-bolt filtering, part links, and torque tools…