2019 Caterpillar 305 Cr Bolt Sizes & Torque Specs

Free OEM-referenced torque and bolt specs for the 2019 Caterpillar 305 Cr.

This page is the OEM-referenced fastener summary for the 2019 Caterpillar 305 Cr. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 2019 Caterpillar 305 Cr, fasteners follow metric standards typical of late-model Caterpillar engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 2019 Caterpillar 305 Cr

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2019 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2019 Caterpillar 305 Cr?

Manufacturer-specified torque values for the 2019 Caterpillar 305 Cr are in the factory service manual or owner's handbook. WhatSizeBolt sources values from manufacturer literature and verifies against community data — if we do not have this exact year listed, check the Caterpillar brand page for the closest model year.

What socket size do I need for the 2019 Caterpillar 305 Cr lug nuts?

Most modern Caterpillar vehicles use a 19mm or 21mm socket. Older Caterpillar models from before 2000 may use a 13/16" SAE socket on certain trims. Confirm against the actual lug before purchasing aftermarket wheels.

Are the 2019 Caterpillar 305 Cr fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Caterpillar 305 Cr years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

All 7 2019 Caterpillar 305 Cr fastener specs

Per-bolt torque, wrench size, and thread spec for the 2019 Caterpillar 305 Cr, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Engine — 2019 Caterpillar 305 Cr

Engine bolt-by-bolt torque for the 2019 Caterpillar 305 Cr, including the long block, valve covers, and intake. For the engine, plan for a 17mm tool on a M14x1.5 stud; final torque is 22 ft-lbs (engine oil drain plug).

Drivetrain — 2019 Caterpillar 305 Cr

Drivetrain and driveline fasteners for the 2019 Caterpillar 305 Cr — axle, transmission, and differential plugs. Final drive drain plug tightens to 30 ft-lbs, takes a 24mm driver, runs on M18x1.5 threads, located at the drivetrain.

Body — 2019 Caterpillar 305 Cr

Body fasteners on the 2019 Caterpillar 305 Cr. The rops mounting bolt uses a 24mm drive on a M16x2.0 thread, torqued to 155 ft-lbs at the body.

Undercarriage — 2019 Caterpillar 305 Cr

Undercarriage fasteners on the 2019 Caterpillar 305 Cr. At the undercarriage, the sprocket bolt torques to 155 ft-lbs (24mm drive, M16x2.0 thread). For the undercarriage, plan for a 24mm tool on a M16x2.0 stud; final torque is 155 ft-lbs (210 Nm) (track bolt).

Attachment — 2019 Caterpillar 305 Cr

Attachment fasteners on the 2019 Caterpillar 305 Cr. For the attachment, plan for a 24mm tool on a M16x2.0 stud; final torque is 155 ft-lbs (swing bearing bolt). Bucket pin retaining bolt tightens to 75 ft-lbs, takes a 18mm driver, runs on M12x1.75 threads, located at the attachment.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2019 Caterpillar 305 Cr numbers above.

Loading the interactive 2019 Caterpillar 305 Cr fastener lookup with per-bolt filtering, part links, and torque tools…