2012 Dodge Avenger Lug Nut Torque & Bolt Specs

The 2012 Dodge Avenger lug nut torque is 110 ft-lbs (150 Nm), tightened with a 19mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 110 ft-lbs (150 Nm) · Socket size: 19mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2012 Dodge Avenger. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Stellantis (Jeep/Ram/Dodge/Chrysler) torque values: Wrangler/Cherokee lug nuts spec 100 ft-lbs (135 Nm), Ram 1500 specs 135 ft-lbs (183 Nm), Ram 2500/3500 specs 160 ft-lbs (217 Nm). Most use a 19mm or 22mm socket with M14x1.5 thread on trucks. The Wrangler's hub-centric ring is critical — do not run hub-piloted wheels without it.

Common fastener categories on the 2012 Dodge Avenger

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2012 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2012 Dodge Avenger?

The OEM-specified lug-nut torque for the 2012 Dodge Avenger is 110 ft-lbs (150 Nm), using a 19mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2012 Dodge Avenger lug nuts?

The 2012 Dodge Avenger uses a 19mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2012 Dodge Avenger fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Dodge Avenger years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2012 Dodge Avenger suspension & steering torque specs (control arm, ball joint, tie rod)

All 17 2012 Dodge Avenger fastener specs

Per-bolt torque, wrench size, and thread spec for the 2012 Dodge Avenger, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 2012 Dodge Avenger

Wheel and lug nut spec for the 2012 Dodge Avenger. Lug nut tightens to 110 ft-lbs (150 Nm), takes a 19mm driver, runs on M12x1.5 threads.

Brakes — 2012 Dodge Avenger

Brake fasteners on the 2012 Dodge Avenger — caliper bracket, slide pins, and banjo bolt torque follow. The front brake caliper bracket bolt, torqued to 80 ft-lbs (108 Nm). The rear brake caliper guide-pin bolt torques to 32 ft-lbs (43 Nm). plan for the right driver; final torque is 32 ft-lbs (43 Nm) (front brake caliper guide-pin bolt).

Engine — 2012 Dodge Avenger

Engine bolt-by-bolt torque for the 2012 Dodge Avenger, including the long block, valve covers, and intake. The engine oil drain plug torques to 25 ft-lbs (34 Nm). plan for the right driver; final torque is 15 ft-lbs (20 Nm) (spark plug).

Drivetrain — 2012 Dodge Avenger

Drivetrain and driveline fasteners for the 2012 Dodge Avenger — axle, transmission, and differential plugs. plan for the right driver; final torque is 118 ft-lbs (160 Nm) (front axle/hub nut).

Suspension — 2012 Dodge Avenger

Suspension and chassis fastener torque for the 2012 Dodge Avenger — strut, control arm, and sway bar values. Lower ball joint pinch bolt tightens to 70 ft-lbs (95 Nm). The front sway bar end-link nut, torqued to 35 ft-lbs (47 Nm). The rear shock lower bolt torques to 73 ft-lbs (99 Nm). plan for the right driver; final torque is 107 ft-lbs (145 Nm) (front lower control arm rear pivot bolt). Rear wheel hub/bearing bolts tightens to 77 ft-lbs (104 Nm). The front wheel hub-to-knuckle bolts, torqued to 35 ft-lbs (47 Nm). The front strut upper mount nuts torques to 40 ft-lbs (54 Nm). plan for the right driver; final torque is 103 ft-lbs (140 Nm) (front strut-to-knuckle bolts). Front lower control arm front pivot bolt tightens to 129 ft-lbs (175 Nm).

Steering — 2012 Dodge Avenger

Steering linkage fasteners on the 2012 Dodge Avenger. The outer tie rod end nut, torqued to 40 ft-lbs (54 Nm).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2012 Dodge Avenger numbers above.

Loading the interactive 2012 Dodge Avenger fastener lookup with per-bolt filtering, part links, and torque tools…