2004 Dodge Ram 2500 Lug Nut Torque & Bolt Specs

The 2004 Dodge Ram 2500 lug nut torque is 100 ft-lbs (135 Nm), tightened with a 24mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 100 ft-lbs (135 Nm) · Socket size: 24mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2004 Dodge Ram 2500. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Stellantis (Jeep/Ram/Dodge/Chrysler) torque values: Wrangler/Cherokee lug nuts spec 100 ft-lbs (135 Nm), Ram 1500 specs 135 ft-lbs (183 Nm), Ram 2500/3500 specs 160 ft-lbs (217 Nm). Most use a 19mm or 22mm socket with M14x1.5 thread on trucks. The Wrangler's hub-centric ring is critical — do not run hub-piloted wheels without it.

Common fastener categories on the 2004 Dodge Ram 2500

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2004 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2004 Dodge Ram 2500?

The OEM-specified lug-nut torque for the 2004 Dodge Ram 2500 is 100 ft-lbs (135 Nm), using a 24mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2004 Dodge Ram 2500 lug nuts?

The 2004 Dodge Ram 2500 uses a 24mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2004 Dodge Ram 2500 fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Dodge Ram 2500 years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2004 Dodge Ram 2500 oil drain plug torque & size

→ 2004 Dodge Ram 2500 suspension & steering torque specs (control arm, ball joint, tie rod)

All 28 2004 Dodge Ram 2500 fastener specs

Per-bolt torque, wrench size, and thread spec for the 2004 Dodge Ram 2500, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 2004 Dodge Ram 2500

Wheel and lug nut spec for the 2004 Dodge Ram 2500. For the all four wheels, plan for a 24mm tool on a M12x1.5 stud; final torque is 100 ft-lbs (135 Nm) (lug nut).

Brakes — 2004 Dodge Ram 2500

Brake fasteners on the 2004 Dodge Ram 2500 — caliper bracket, slide pins, and banjo bolt torque follow. Front caliper slide pin tightens to 25-35 ft-lbs, takes a 13mm driver, runs on M10x1.5 threads, located at the front caliper. The front brake caliper bracket bolt uses a 18mm drive on a M14x2.0 thread, torqued to 125 ft-lbs at the front axle, caliper bracket.

Engine — 2004 Dodge Ram 2500

Engine bolt-by-bolt torque for the 2004 Dodge Ram 2500, including the long block, valve covers, and intake. The engine mount bolt uses a 18mm drive on a M12x1.75 thread, torqued to 70 lb-ft at the engine mount. At the engine block, the oil filter torques to Hand Tight + 3/4 Turn (Oil Filter Wrench drive, 3/4-16 UNF thread). For the cylinder head, plan for a 9/16" tool on a M14x1.25 stud; final torque is 20-30 ft-lbs (spark plug). Glow plug tightens to 15 ft-lbs, takes a 12mm driver, runs on M12x1.25 threads, located at the cylinder head. The oil drain plug uses a 15mm drive on a M14x1.5 thread, torqued to 20 ft-lbs (27 Nm) at the oil pan. At the valve cover, the valve cover bolt torques to 9 lb-ft (10mm drive, M8x1.25 thread).

Drivetrain — 2004 Dodge Ram 2500

Drivetrain and driveline fasteners for the 2004 Dodge Ram 2500 — axle, transmission, and differential plugs. At the front differential, the front differential fill plug torques to 25 ft-lbs (See notes drive, 3/8" sq thread). For the transfer case, plan for a 24mm tool on a M20x1.5 stud; final torque is 20-25 ft-lbs (transfer case drain plug).

Suspension — 2004 Dodge Ram 2500

Suspension and chassis fastener torque for the 2004 Dodge Ram 2500 — strut, control arm, and sway bar values. For the lower control arm, plan for a 21mm tool on a M14x1.5 stud; final torque is 130 lb-ft (lower control arm bolt). Upper control arm bolt tightens to 100 lb-ft, takes a 18mm driver, runs on M12x1.75 threads, located at the upper control arm. The rear leaf spring u-bolt nut uses a 22mm drive on a M14x2.0 thread, torqued to 135-175 ft-lbs at the rear leaf spring. At the shock lower mount, the shock absorber bottom bolt torques to 100 lb-ft (18mm drive, M12x1.75 thread). For the shock top mount, plan for a 18mm tool on a M12x1.75 stud; final torque is 25 lb-ft (shock absorber top nut). Sway bar link nut tightens to 75 lb-ft, takes a 15mm driver, runs on M10x1.5 threads, located at the sway bar link.

Steering — 2004 Dodge Ram 2500

Steering linkage fasteners on the 2004 Dodge Ram 2500. Tie rod end nut tightens to 60-75 ft-lbs, takes a 22mm driver, runs on M14x1.5 threads, located at the tie rod end.

Transmission — 2004 Dodge Ram 2500

Transmission fasteners on the 2004 Dodge Ram 2500. The transmission crossmember bolt uses a 18mm drive on a M12x1.75 thread, torqued to 70 lb-ft at the crossmember. At the transmission mount, the transmission mount bolt torques to 50 lb-ft (15mm drive, M10x1.5 thread). For the transmission pan, plan for a 8mm tool on a M8x1.25 stud; final torque is 14 ft-lbs (transmission pan bolt).

Axle / Drivetrain — 2004 Dodge Ram 2500

Axle / Drivetrain fasteners on the 2004 Dodge Ram 2500. At the front wheel hub, the front axle hub nut (4wd) torques to 160-180 ft-lbs (See notes drive, M34x1.5 thread).

Brake — 2004 Dodge Ram 2500

Brake fasteners on the 2004 Dodge Ram 2500. For the brake line to caliper, plan for a 14mm tool on a M10x1.0 stud; final torque is 23 lb-ft (brake line banjo bolt). Brake caliper slide pin bolt tightens to 27 lb-ft, takes a 13mm driver, runs on M10x1.5 threads, located at the caliper slide pin. The brake rotor set screw uses a T30 drive on a M6x1.0 thread, torqued to 10 lb-ft at the rotor to hub. At the caliper to bracket, the brake caliper bolt torques to 80 lb-ft (18mm drive, M12x1.75 thread).

Wheel — 2004 Dodge Ram 2500

Wheel fasteners on the 2004 Dodge Ram 2500. Center cap clip tightens to Hand Tight, takes a N/A driver, runs on N/A threads, located at the wheel center. The wheel stud uses a N/A drive on a M14x1.5 thread, torqued to Press Fit at the wheel hub.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2004 Dodge Ram 2500 numbers above.

Loading the interactive 2004 Dodge Ram 2500 fastener lookup with per-bolt filtering, part links, and torque tools…