2002 Ford F 350 Super Duty Lug Nut Torque & Bolt Specs

The 2002 Ford F 350 Super Duty lug nut torque is 165 ft-lbs (224 Nm), tightened with a 21mm socket on M14 x 1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass. The wheel bolt pattern is 8x170.

Lug nut torque: 165 ft-lbs (224 Nm) · Socket size: 21mm · Thread: M14 x 1.5 · Bolt pattern: 8x170.

This page is the OEM-referenced fastener summary for the 2002 Ford F 350 Super Duty. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Ford lug-nut torque varies more by chassis than most makes — 100 ft-lbs for Focus/Fusion/Fiesta, 150 ft-lbs for half-ton F-150, and 165 ft-lbs for Super Duty F-250/F-350. F-150s from 2004-2014 use a 21mm OEM socket, while 2015+ aluminum-body trucks moved to the larger 22mm. Ford torque-to-yield (TTY) head bolts are standard from the early 2000s — do not reuse them, ever.

Common fastener categories on the 2002 Ford F 350 Super Duty

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2002 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2002 Ford F 350 Super Duty?

The OEM-specified lug-nut torque for the 2002 Ford F 350 Super Duty is 165 ft-lbs (224 Nm), using a 21mm socket on M14 x 1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2002 Ford F 350 Super Duty lug nuts?

The 2002 Ford F 350 Super Duty uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2002 Ford F 350 Super Duty fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Ford F 350 Super Duty years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2002 Ford F 350 Super Duty oil drain plug torque & size

→ 2002 Ford F 350 Super Duty suspension & steering torque specs (control arm, ball joint, tie rod)

All 68 2002 Ford F 350 Super Duty fastener specs

Per-bolt torque, wrench size, and thread spec for the 2002 Ford F 350 Super Duty, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 2002 Ford F 350 Super Duty

Wheel and lug nut spec for the 2002 Ford F 350 Super Duty. For the wheel hub, plan for a 21mm tool on a M14 x 1.5 stud; final torque is 165 ft-lbs (224 Nm) (wheel lug nut). Wheel lug nut (m14x1.5) tightens to 165 ft-lbs (224 Nm), takes a 21mm driver, runs on M14x1.5 threads, located at the wheels.

Brakes — 2002 Ford F 350 Super Duty

Brake fasteners on the 2002 Ford F 350 Super Duty — caliper bracket, slide pins, and banjo bolt torque follow. Caliper bracket bolt tightens to 85 ft-lbs, takes a 14mm driver, runs on M12x1.25 threads, located at the steering knuckle. The brake bleeder valve uses a 8mm drive on a M8x1.0 thread, torqued to 8 ft-lbs at the caliper. At the hub, the rotor set screw torques to 4 ft-lbs (5mm drive, M5x0.8 thread). For the caliper, plan for a 10mm tool on a M10x1.0 stud; final torque is 25 ft-lbs (brake line banjo bolt). Brake line bracket tightens to 8 ft-lbs, takes a 10mm driver, runs on M6x1.0 threads, located at the frame. The front brake caliper bracket bolt uses a 21mm drive on a M14x2.0 thread, torqued to 166-228 ft-lbs at the front axle - caliper bracket. At the front axle - caliper, the front brake caliper slide pin torques to 21-26 ft-lbs (13mm drive, M10x1.5 thread).

Engine — 2002 Ford F 350 Super Duty

Engine bolt-by-bolt torque for the 2002 Ford F 350 Super Duty, including the long block, valve covers, and intake. The oil drain plug (m15x1.5) uses a 15mm drive on a M15x1.5 thread, torqued to 25-30 ft-lbs at the oil pan. At the engine block, the oil filter housing torques to 18 ft-lbs (24mm drive, M20x1.5 thread). For the oil pan perimeter, plan for a 10mm tool on a M6x1.0 stud; final torque is 9 ft-lbs (oil pan bolt). Oil cooler line tightens to 22 ft-lbs, takes a 17mm driver, runs on M12x1.5 threads, located at the oil cooler. The spark plug (m14x1.25) uses a 16mm drive on a M14x1.25 thread, torqued to 15-20 ft-lbs at the cylinder head.

Drivetrain — 2002 Ford F 350 Super Duty

Drivetrain and driveline fasteners for the 2002 Ford F 350 Super Duty — axle, transmission, and differential plugs. At the transfer case, the transfer case drain plug torques to 14-22 ft-lbs (24mm drive, M18x1.5 thread). For the front & rear differential, plan for a 3/8" sq drive tool on a 3/8" square drive stud; final torque is 15-30 ft-lbs (differential drain/fill plug). Transmission pan bolt tightens to 8-12 ft-lbs, takes a 8mm driver, runs on M8x1.25 threads, located at the transmission pan.

Suspension — 2002 Ford F 350 Super Duty

Suspension and chassis fastener torque for the 2002 Ford F 350 Super Duty — strut, control arm, and sway bar values. For the sway bar, plan for a 14mm tool on a M10x1.25 stud; final torque is 29 ft-lbs (sway bar link nut). Wheel hub bolt tightens to 80 ft-lbs, takes a 17mm driver, runs on M12x1.25 threads, located at the knuckle. The control arm bolt uses a 19mm drive on a M14x2.0 thread, torqued to 85 ft-lbs at the subframe. At the control arm, the lower ball joint nut torques to 94 ft-lbs (19mm drive, M14x2.0 thread). For the strut tower, plan for a 14mm tool on a M10x1.25 stud; final torque is 47 ft-lbs (strut mount nut).

Steering — 2002 Ford F 350 Super Duty

Steering linkage fasteners on the 2002 Ford F 350 Super Duty. Steering rack bolt tightens to 74 ft-lbs, takes a 17mm driver, runs on M12x1.25 threads, located at the subframe. The steering column u-joint uses a 12mm drive on a M8x1.25 thread, torqued to 22 ft-lbs at the column. At the tie rod, the tie rod lock nut torques to 41 ft-lbs (17mm drive, M12x1.25 thread).

Body — 2002 Ford F 350 Super Duty

Body fasteners on the 2002 Ford F 350 Super Duty. The bumper bolt uses a 12mm drive on a M8x1.25 thread, torqued to 15 ft-lbs at the frame. At the body, the fender bolt torques to 8 ft-lbs (10mm drive, M6x1.0 thread). For the body, plan for a 14mm tool on a M10x1.25 stud; final torque is 27 ft-lbs (door hinge bolt).

Exhaust — 2002 Ford F 350 Super Duty

Exhaust fasteners on the 2002 Ford F 350 Super Duty. At the cat flange, the catalytic bolt torques to 33 ft-lbs (14mm drive, M10x1.25 thread). For the frame, plan for a 12mm tool on a M8x1.25 stud; final torque is 15 ft-lbs (muffler hanger bolt). O2 sensor tightens to 30 ft-lbs, takes a 22mm driver, runs on M18x1.5 threads, located at the various. The exhaust flange bolt uses a 14mm drive on a M10x1.25 thread, torqued to 33 ft-lbs at the manifold.

Electrical — 2002 Ford F 350 Super Duty

Electrical fasteners on the 2002 Ford F 350 Super Duty. For the solenoid, plan for a 10mm tool on a M6x1.0 stud; final torque is 70 in-lbs (starter solenoid terminal nut). Starter heat shield bolt tightens to 8 ft-lbs, takes a 10mm driver, runs on M6x1.0 threads, located at the starter body. The starter support bracket bolt uses a 12mm drive on a M8x1.25 thread, torqued to 22 ft-lbs at the block/transmission. At the alternator, the alternator terminal nut torques to 70 in-lbs (10mm drive, M6x1.0 thread). For the block, plan for a 10mm tool on a M6x1.0 stud; final torque is 8 ft-lbs (starter ground strap bolt). Alternator b+ terminal nut tightens to 15 ft-lbs, takes a 13mm driver, runs on M8x1.25 threads, located at the alternator. The belt tensioner lock bolt uses a 12mm drive on a M8x1.25 thread, torqued to 22 ft-lbs at the tensioner body. At the starter, the starter b+ terminal nut torques to 15 ft-lbs (13mm drive, M8x1.25 thread). For the bell housing, plan for a 14mm tool on a M10x1.25 stud; final torque is See sequence: 1) 30 ft-lbs 2) 55 ft-lbs final (starter mounting bolt). Belt tensioner pivot bolt tightens to 35 ft-lbs, takes a 15mm driver, runs on M10x1.5 threads, located at the block. The alternator ground strap bolt uses a 10mm drive on a M6x1.0 thread, torqued to 8 ft-lbs at the block. At the block, the alternator support bracket bolt torques to 22 ft-lbs (12mm drive, M8x1.25 thread).

Suspension & Steering — 2002 Ford F 350 Super Duty

Suspension & Steering fasteners on the 2002 Ford F 350 Super Duty. Front hub/wheel bearing nut tightens to 482-610 ft-lbs, takes a Special hub nut socket driver, runs on M34x1.5 threads, located at the front axle hub. The front leaf spring u-bolt nut uses a 22mm drive on a M14x2.0 thread, torqued to 148-202 ft-lbs at the front suspension - leaf spring. At the front steering - tie rod end, the tie rod end nut torques to 52-75 ft-lbs (22mm drive, M14x1.5 thread). For the rear suspension - leaf spring, plan for a 22mm tool on a M14x2.0 stud; final torque is 148-202 ft-lbs (rear leaf spring u-bolt nut).

Wheels & Tires — 2002 Ford F 350 Super Duty

Wheels & Tires fasteners on the 2002 Ford F 350 Super Duty. The outer rear lug nut (drw) uses a 22mm drive on a M14x1.5 thread, torqued to 165 ft-lbs (224 Nm) at the rear wheel - outer. At the rear wheel - inner, the inner rear lug nut (drw) torques to 165 ft-lbs (224 Nm) (22mm drive, M14x1.5 thread). For the all wheels, plan for a 22mm tool on a M14x1.5 stud; final torque is 165 ft-lbs (224 Nm) (lug nut). Front lug nut tightens to 165 ft-lbs (224 Nm), takes a 22mm driver, runs on M14x1.5 threads, located at the front wheel.

Engine - Ignition — 2002 Ford F 350 Super Duty

Engine - Ignition fasteners on the 2002 Ford F 350 Super Duty. At the cylinder head, the spark plug torques to 26-30 ft-lbs (9/16" drive, M14x1.25 thread).

Engine - Lubrication — 2002 Ford F 350 Super Duty

Engine - Lubrication fasteners on the 2002 Ford F 350 Super Duty. For the oil pan, plan for a 15mm tool on a M14x1.5 stud; final torque is 18-22 ft-lbs (oil drain plug).

HVAC — 2002 Ford F 350 Super Duty

HVAC fasteners on the 2002 Ford F 350 Super Duty. Caliper guide pin tightens to 22 ft-lbs, takes a 12mm driver, runs on M8x1.25 threads, located at the caliper bracket. The power steering pump uses a 12mm drive on a M8x1.25 thread, torqued to 15 ft-lbs at the bracket. At the bracket, the idler pulley bolt torques to 35 ft-lbs (15mm drive, M10x1.5 thread). For the bracket, plan for a 14mm tool on a M10x1.5 stud; final torque is See sequence (alternator pivot bolt).

Exterior — 2002 Ford F 350 Super Duty

Exterior fasteners on the 2002 Ford F 350 Super Duty. The hood hinge bolt uses a 12mm drive on a M8x1.25 thread, torqued to 15 ft-lbs at the hood.

Transmission — 2002 Ford F 350 Super Duty

Transmission fasteners on the 2002 Ford F 350 Super Duty. At the trans case, the trans cooler line torques to 22 ft-lbs (17mm drive, M12x1.25 thread). For the crossmember, plan for a 17mm tool on a M12x1.25 stud; final torque is 54 ft-lbs (trans mount bolt). Transmission pan bolt (m8x1.25) tightens to 12-14 ft-lbs, takes a 13mm driver, runs on M8x1.25 threads, located at the transmission pan. The shift cable bracket uses a 12mm drive on a M8x1.25 thread, torqued to 15 ft-lbs at the trans case. At the trans pan, the trans pan bolt torques to 8 ft-lbs (10mm drive, M6x1.0 thread). For the trans pan, plan for a 14mm tool on a M12x1.25 stud; final torque is 29 ft-lbs (trans drain plug).

Interior — 2002 Ford F 350 Super Duty

Interior fasteners on the 2002 Ford F 350 Super Duty. For the floor, plan for a 14mm tool on a M10x1.25 stud; final torque is 34 ft-lbs (seat track bolt). Seat belt bolt tightens to 47 ft-lbs, takes a 17mm driver, runs on M12x1.25 threads, located at the body.

Fuel System — 2002 Ford F 350 Super Duty

Fuel System fasteners on the 2002 Ford F 350 Super Duty. Fuel filter housing bolt tightens to 18-22 ft-lbs, takes a 13mm driver, runs on M8x1.25 threads, located at the fuel filter housing.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2002 Ford F 350 Super Duty numbers above.

Loading the interactive 2002 Ford F 350 Super Duty fastener lookup with per-bolt filtering, part links, and torque tools…