2004 Ford F 350 Super Duty Lug Nut Torque & Bolt Specs

The 2004 Ford F 350 Super Duty lug nut torque is 165 ft-lbs (224 Nm), tightened with a 22mm socket on M14x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 165 ft-lbs (224 Nm) · Socket size: 22mm · Thread: M14x1.5.

This page is the OEM-referenced fastener summary for the 2004 Ford F 350 Super Duty. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Ford lug-nut torque varies more by chassis than most makes — 100 ft-lbs for Focus/Fusion/Fiesta, 150 ft-lbs for half-ton F-150, and 165 ft-lbs for Super Duty F-250/F-350. F-150s from 2004-2014 use a 21mm OEM socket, while 2015+ aluminum-body trucks moved to the larger 22mm. Ford torque-to-yield (TTY) head bolts are standard from the early 2000s — do not reuse them, ever.

Common fastener categories on the 2004 Ford F 350 Super Duty

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2004 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2004 Ford F 350 Super Duty?

The OEM-specified lug-nut torque for the 2004 Ford F 350 Super Duty is 165 ft-lbs (224 Nm), using a 22mm socket on M14x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2004 Ford F 350 Super Duty lug nuts?

The 2004 Ford F 350 Super Duty uses a 22mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2004 Ford F 350 Super Duty fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Ford F 350 Super Duty years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2004 Ford F 350 Super Duty oil drain plug torque & size

→ 2004 Ford F 350 Super Duty suspension & steering torque specs (control arm, ball joint, tie rod)

All 61 2004 Ford F 350 Super Duty fastener specs

Per-bolt torque, wrench size, and thread spec for the 2004 Ford F 350 Super Duty, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 2004 Ford F 350 Super Duty

Wheel and lug nut spec for the 2004 Ford F 350 Super Duty. The wheel lug nut (m14x1.5) uses a 21mm drive on a M14x1.5 thread, torqued to 165 ft-lbs (224 Nm) at the wheels. At the wheel hub, the wheel lug nut torques to 165 ft-lbs (224 Nm) (21mm drive, M14x1.5 thread).

Brakes — 2004 Ford F 350 Super Duty

Brake fasteners on the 2004 Ford F 350 Super Duty — caliper bracket, slide pins, and banjo bolt torque follow. At the caliper, the brake bleeder valve torques to 8 ft-lbs (8mm drive, M8x1.0 thread). For the caliper, plan for a 10mm tool on a M10x1.0 stud; final torque is 25 ft-lbs (brake line banjo bolt). Caliper bracket bolt tightens to 85 ft-lbs, takes a 14mm driver, runs on M12x1.25 threads, located at the steering knuckle. The rotor set screw uses a 5mm drive on a M5x0.8 thread, torqued to 4 ft-lbs at the hub. At the front axle - caliper, the front brake caliper slide pin torques to 21-26 ft-lbs (13mm drive, M10x1.5 thread). For the frame, plan for a 10mm tool on a M6x1.0 stud; final torque is 8 ft-lbs (brake line bracket). Front brake caliper bracket bolt tightens to 166-228 ft-lbs, takes a 21mm driver, runs on M14x2.0 threads, located at the front axle - caliper bracket.

Engine — 2004 Ford F 350 Super Duty

Engine bolt-by-bolt torque for the 2004 Ford F 350 Super Duty, including the long block, valve covers, and intake. For the oil cooler, plan for a 17mm tool on a M12x1.5 stud; final torque is 22 ft-lbs (oil cooler line). Spark plug (m14x1.25) tightens to 15-20 ft-lbs, takes a 16mm driver, runs on M14x1.25 threads, located at the cylinder head. The oil filter housing uses a 24mm drive on a M20x1.5 thread, torqued to 18 ft-lbs at the engine block. At the oil pan, the oil drain plug (m15x1.5) torques to 25-30 ft-lbs (15mm drive, M15x1.5 thread).

Drivetrain — 2004 Ford F 350 Super Duty

Drivetrain and driveline fasteners for the 2004 Ford F 350 Super Duty — axle, transmission, and differential plugs. Differential drain/fill plug tightens to 15-30 ft-lbs, takes a 3/8" sq drive driver, runs on 3/8" square drive threads, located at the front & rear differential. The transfer case drain plug uses a 24mm drive on a M18x1.5 thread, torqued to 14-22 ft-lbs at the transfer case. At the transmission pan, the transmission pan bolt torques to 8-12 ft-lbs (8mm drive, M8x1.25 thread).

Suspension — 2004 Ford F 350 Super Duty

Suspension and chassis fastener torque for the 2004 Ford F 350 Super Duty — strut, control arm, and sway bar values. The control arm bolt uses a 19mm drive on a M14x2.0 thread, torqued to 85 ft-lbs at the subframe. At the knuckle, the wheel hub bolt torques to 80 ft-lbs (17mm drive, M12x1.25 thread). For the control arm, plan for a 19mm tool on a M14x2.0 stud; final torque is 94 ft-lbs (lower ball joint nut). Sway bar link nut tightens to 29 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the sway bar.

Steering — 2004 Ford F 350 Super Duty

Steering linkage fasteners on the 2004 Ford F 350 Super Duty. At the tie rod, the tie rod lock nut torques to 41 ft-lbs (17mm drive, M12x1.25 thread). For the subframe, plan for a 17mm tool on a M12x1.25 stud; final torque is 74 ft-lbs (steering rack bolt). Steering column u-joint tightens to 22 ft-lbs, takes a 12mm driver, runs on M8x1.25 threads, located at the column.

Body — 2004 Ford F 350 Super Duty

Body fasteners on the 2004 Ford F 350 Super Duty. For the frame, plan for a 12mm tool on a M8x1.25 stud; final torque is 15 ft-lbs (bumper bolt). Door hinge bolt tightens to 27 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the body.

Exhaust — 2004 Ford F 350 Super Duty

Exhaust fasteners on the 2004 Ford F 350 Super Duty. O2 sensor tightens to 30 ft-lbs, takes a 22mm driver, runs on M18x1.5 threads, located at the various. The exhaust flange bolt uses a 14mm drive on a M10x1.25 thread, torqued to 33 ft-lbs at the manifold. At the cat flange, the catalytic bolt torques to 33 ft-lbs (14mm drive, M10x1.25 thread). For the frame, plan for a 12mm tool on a M8x1.25 stud; final torque is 15 ft-lbs (muffler hanger bolt).

Electrical — 2004 Ford F 350 Super Duty

Electrical fasteners on the 2004 Ford F 350 Super Duty. The alternator ground strap bolt uses a 10mm drive on a M6x1.0 thread, torqued to 8 ft-lbs at the block. At the starter, the starter b+ terminal nut torques to 15 ft-lbs (13mm drive, M8x1.25 thread). For the solenoid, plan for a 10mm tool on a M6x1.0 stud; final torque is 70 in-lbs (starter solenoid terminal nut). Starter ground strap bolt tightens to 8 ft-lbs, takes a 10mm driver, runs on M6x1.0 threads, located at the block. The belt tensioner lock bolt uses a 12mm drive on a M8x1.25 thread, torqued to 22 ft-lbs at the tensioner body. At the alternator, the alternator terminal nut torques to 70 in-lbs (10mm drive, M6x1.0 thread). For the starter body, plan for a 10mm tool on a M6x1.0 stud; final torque is 8 ft-lbs (starter heat shield bolt). Alternator b+ terminal nut tightens to 15 ft-lbs, takes a 13mm driver, runs on M8x1.25 threads, located at the alternator. The starter mounting bolt uses a 14mm drive on a M10x1.25 thread, torqued to See sequence: 1) 30 ft-lbs 2) 55 ft-lbs final at the bell housing. At the block, the belt tensioner pivot bolt torques to 35 ft-lbs (15mm drive, M10x1.5 thread). For the block, plan for a 12mm tool on a M8x1.25 stud; final torque is 22 ft-lbs (alternator support bracket bolt). Starter support bracket bolt tightens to 22 ft-lbs, takes a 12mm driver, runs on M8x1.25 threads, located at the block/transmission.

Wheels & Tires — 2004 Ford F 350 Super Duty

Wheels & Tires fasteners on the 2004 Ford F 350 Super Duty. At the rear wheel - outer, the outer rear lug nut (drw) torques to 165 ft-lbs (224 Nm) (22mm drive, M14x1.5 thread). For the front wheel, plan for a 22mm tool on a M14x1.5 stud; final torque is 165 ft-lbs (224 Nm) (front lug nut). Lug nut tightens to 165 ft-lbs (224 Nm), takes a 22mm driver, runs on M14x1.5 threads, located at the all wheels. The inner rear lug nut (drw) uses a 22mm drive on a M14x1.5 thread, torqued to 165 ft-lbs (224 Nm) at the rear wheel - inner.

Suspension & Steering — 2004 Ford F 350 Super Duty

Suspension & Steering fasteners on the 2004 Ford F 350 Super Duty. For the front steering - tie rod end, plan for a 22mm tool on a M14x1.5 stud; final torque is 52-75 ft-lbs (tie rod end nut). Front hub/wheel bearing nut tightens to 482-610 ft-lbs, takes a Special hub nut socket driver, runs on M34x1.5 threads, located at the front axle hub. The front leaf spring u-bolt nut uses a 22mm drive on a M14x2.0 thread, torqued to 148-202 ft-lbs at the front suspension - leaf spring. At the rear suspension - leaf spring, the rear leaf spring u-bolt nut torques to 148-202 ft-lbs (22mm drive, M14x2.0 thread).

Engine - Ignition — 2004 Ford F 350 Super Duty

Engine - Ignition fasteners on the 2004 Ford F 350 Super Duty. Spark plug tightens to 26-30 ft-lbs, takes a 9/16" driver, runs on M14x1.25 threads, located at the cylinder head.

Engine - Lubrication — 2004 Ford F 350 Super Duty

Engine - Lubrication fasteners on the 2004 Ford F 350 Super Duty. The oil drain plug uses a 15mm drive on a M14x1.5 thread, torqued to 18-22 ft-lbs at the oil pan.

Interior — 2004 Ford F 350 Super Duty

Interior fasteners on the 2004 Ford F 350 Super Duty. At the floor, the seat track bolt torques to 34 ft-lbs (14mm drive, M10x1.25 thread). For the body, plan for a 17mm tool on a M12x1.25 stud; final torque is 47 ft-lbs (seat belt bolt).

Exterior — 2004 Ford F 350 Super Duty

Exterior fasteners on the 2004 Ford F 350 Super Duty. For the hood, plan for a 12mm tool on a M8x1.25 stud; final torque is 15 ft-lbs (hood hinge bolt).

Transmission — 2004 Ford F 350 Super Duty

Transmission fasteners on the 2004 Ford F 350 Super Duty. Shift cable bracket tightens to 15 ft-lbs, takes a 12mm driver, runs on M8x1.25 threads, located at the trans case. The trans pan bolt uses a 10mm drive on a M6x1.0 thread, torqued to 8 ft-lbs at the trans pan. At the crossmember, the trans mount bolt torques to 54 ft-lbs (17mm drive, M12x1.25 thread). For the transmission pan, plan for a 13mm tool on a M8x1.25 stud; final torque is 12-14 ft-lbs (transmission pan bolt (m8x1.25)). Trans drain plug tightens to 29 ft-lbs, takes a 14mm driver, runs on M12x1.25 threads, located at the trans pan. The trans cooler line uses a 17mm drive on a M12x1.25 thread, torqued to 22 ft-lbs at the trans case.

Fuel System — 2004 Ford F 350 Super Duty

Fuel System fasteners on the 2004 Ford F 350 Super Duty. The fuel filter housing bolt uses a 13mm drive on a M8x1.25 thread, torqued to 18-22 ft-lbs at the fuel filter housing.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2004 Ford F 350 Super Duty numbers above.

Loading the interactive 2004 Ford F 350 Super Duty fastener lookup with per-bolt filtering, part links, and torque tools…