2011 Ford F 350 Super Duty Lug Nut Torque & Bolt Specs

The 2011 Ford F 350 Super Duty lug nut torque is 165 ft-lbs (224 Nm), tightened with a 22mm socket on M14x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass. The wheel bolt pattern is 8x170.

Lug nut torque: 165 ft-lbs (224 Nm) · Socket size: 22mm · Thread: M14x1.5 · Bolt pattern: 8x170.

This page is the OEM-referenced fastener summary for the 2011 Ford F 350 Super Duty. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Ford lug-nut torque varies more by chassis than most makes — 100 ft-lbs for Focus/Fusion/Fiesta, 150 ft-lbs for half-ton F-150, and 165 ft-lbs for Super Duty F-250/F-350. F-150s from 2004-2014 use a 21mm OEM socket, while 2015+ aluminum-body trucks moved to the larger 22mm. Ford torque-to-yield (TTY) head bolts are standard from the early 2000s — do not reuse them, ever.

Common fastener categories on the 2011 Ford F 350 Super Duty

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2011 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2011 Ford F 350 Super Duty?

The OEM-specified lug-nut torque for the 2011 Ford F 350 Super Duty is 165 ft-lbs (224 Nm), using a 22mm socket on M14x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2011 Ford F 350 Super Duty lug nuts?

The 2011 Ford F 350 Super Duty uses a 22mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2011 Ford F 350 Super Duty fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Ford F 350 Super Duty years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2011 Ford F 350 Super Duty oil drain plug torque & size

→ 2011 Ford F 350 Super Duty suspension & steering torque specs (control arm, ball joint, tie rod)

All 20 2011 Ford F 350 Super Duty fastener specs

Per-bolt torque, wrench size, and thread spec for the 2011 Ford F 350 Super Duty, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 2011 Ford F 350 Super Duty

Wheel and lug nut spec for the 2011 Ford F 350 Super Duty. For the wheel hub, plan for a 21mm tool on a M14 x 1.5 stud; final torque is 165 ft-lbs (224 Nm) (wheel lug nut). Wheel lug nut (m14x1.5) tightens to 165 ft-lbs (224 Nm), takes a 21mm driver, runs on M14x1.5 threads, located at the wheels.

Brakes — 2011 Ford F 350 Super Duty

Brake fasteners on the 2011 Ford F 350 Super Duty — caliper bracket, slide pins, and banjo bolt torque follow. Front brake caliper slide pin tightens to 21-26 ft-lbs, takes a 13mm driver, runs on M10x1.5 threads, located at the front axle - caliper. The front brake caliper bracket bolt uses a 21mm drive on a M14x2.0 thread, torqued to 166-228 ft-lbs at the front axle - caliper bracket.

Engine — 2011 Ford F 350 Super Duty

Engine bolt-by-bolt torque for the 2011 Ford F 350 Super Duty, including the long block, valve covers, and intake. The spark plug (m14x1.25) uses a 16mm drive on a M14x1.25 thread, torqued to 15-20 ft-lbs at the cylinder head. At the oil pan, the oil drain plug (m15x1.5) torques to 25-30 ft-lbs (15mm drive, M15x1.5 thread).

Drivetrain — 2011 Ford F 350 Super Duty

Drivetrain and driveline fasteners for the 2011 Ford F 350 Super Duty — axle, transmission, and differential plugs. At the front & rear differential, the differential drain/fill plug torques to 15-30 ft-lbs (3/8" sq drive drive, 3/8" square drive thread). For the transfer case, plan for a 24mm tool on a M18x1.5 stud; final torque is 14-22 ft-lbs (transfer case drain plug). Transmission pan bolt tightens to 8-12 ft-lbs, takes a 8mm driver, runs on M8x1.25 threads, located at the transmission pan.

Suspension & Steering — 2011 Ford F 350 Super Duty

Suspension & Steering fasteners on the 2011 Ford F 350 Super Duty. For the rear suspension - leaf spring, plan for a 22mm tool on a M14x2.0 stud; final torque is 148-202 ft-lbs (rear leaf spring u-bolt nut). Tie rod end nut tightens to 52-75 ft-lbs, takes a 22mm driver, runs on M14x1.5 threads, located at the front steering - tie rod end. The front hub/wheel bearing nut uses a Special hub nut socket drive on a M34x1.5 thread, torqued to 482-610 ft-lbs at the front axle hub.

Engine - Ignition — 2011 Ford F 350 Super Duty

Engine - Ignition fasteners on the 2011 Ford F 350 Super Duty. Spark plug tightens to 26-30 ft-lbs, takes a 9/16" driver, runs on M14x1.25 threads, located at the cylinder head.

Wheels & Tires — 2011 Ford F 350 Super Duty

Wheels & Tires fasteners on the 2011 Ford F 350 Super Duty. The inner rear lug nut (drw) uses a 22mm drive on a M14x1.5 thread, torqued to 165 ft-lbs (224 Nm) at the rear wheel - inner. At the rear wheel - outer, the outer rear lug nut (drw) torques to 165 ft-lbs (224 Nm) (22mm drive, M14x1.5 thread). For the all wheels, plan for a 22mm tool on a M14x1.5 stud; final torque is 165 ft-lbs (224 Nm) (lug nut). Front lug nut tightens to 165 ft-lbs (224 Nm), takes a 22mm driver, runs on M14x1.5 threads, located at the front wheel.

Engine - Lubrication — 2011 Ford F 350 Super Duty

Engine - Lubrication fasteners on the 2011 Ford F 350 Super Duty. At the oil pan, the oil drain plug torques to 18-22 ft-lbs (15mm drive, M14x1.5 thread).

Fuel System — 2011 Ford F 350 Super Duty

Fuel System fasteners on the 2011 Ford F 350 Super Duty. For the fuel filter housing, plan for a 13mm tool on a M8x1.25 stud; final torque is 18-22 ft-lbs (fuel filter housing bolt).

Transmission — 2011 Ford F 350 Super Duty

Transmission fasteners on the 2011 Ford F 350 Super Duty. Transmission pan bolt (m8x1.25) tightens to 12-14 ft-lbs, takes a 13mm driver, runs on M8x1.25 threads, located at the transmission pan.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2011 Ford F 350 Super Duty numbers above.

Loading the interactive 2011 Ford F 350 Super Duty fastener lookup with per-bolt filtering, part links, and torque tools…