2008–2009 Ford Taurus Lug Nut Torque & Bolt Specs

The 2009 Ford Taurus lug nut torque is 100 ft-lbs (135 Nm), tightened with a 19mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 100 ft-lbs (135 Nm) · Socket size: 19mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2009 Ford Taurus. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

These specifications also apply to the 2008 model years — identical specs on file for each year.

Ford lug-nut torque varies more by chassis than most makes — 100 ft-lbs for Focus/Fusion/Fiesta, 150 ft-lbs for half-ton F-150, and 165 ft-lbs for Super Duty F-250/F-350. F-150s from 2004-2014 use a 21mm OEM socket, while 2015+ aluminum-body trucks moved to the larger 22mm. Ford torque-to-yield (TTY) head bolts are standard from the early 2000s — do not reuse them, ever.

Common fastener categories on the 2009 Ford Taurus

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2009 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2009 Ford Taurus?

The OEM-specified lug-nut torque for the 2009 Ford Taurus is 100 ft-lbs (135 Nm), using a 19mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2009 Ford Taurus lug nuts?

The 2009 Ford Taurus uses a 19mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2009 Ford Taurus fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Ford Taurus years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2009 Ford Taurus suspension & steering torque specs (control arm, ball joint, tie rod)

All 8 2009 Ford Taurus fastener specs

Per-bolt torque, wrench size, and thread spec for the 2009 Ford Taurus, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 2009 Ford Taurus

Wheel and lug nut spec for the 2009 Ford Taurus. Lug nut tightens to 100 ft-lbs (135 Nm), takes a 19mm driver, runs on M12x1.5 threads.

Engine — 2009 Ford Taurus

Engine bolt-by-bolt torque for the 2009 Ford Taurus, including the long block, valve covers, and intake. The engine oil drain plug, torqued to 20 ft-lbs (27 Nm). The spark plug torques to 12 ft-lbs (16 Nm).

Drivetrain — 2009 Ford Taurus

Drivetrain and driveline fasteners for the 2009 Ford Taurus — axle, transmission, and differential plugs. The front wheel hub/axle nut torques to 184 ft-lbs (250 Nm).

Suspension — 2009 Ford Taurus

Suspension and chassis fastener torque for the 2009 Ford Taurus — strut, control arm, and sway bar values. plan for the right driver; final torque is 59 ft-lbs (80 Nm) (front lower ball joint nut). Front strut lower bolts tightens to 85 ft-lbs (115 Nm).

Steering — 2009 Ford Taurus

Steering linkage fasteners on the 2009 Ford Taurus. Outer tie rod nut tightens to 41 ft-lbs (56 Nm).

Transmission — 2009 Ford Taurus

Transmission fasteners on the 2009 Ford Taurus. The transmission fluid pan bolts, torqued to 8 ft-lbs (11 Nm).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2009 Ford Taurus numbers above.

Loading the interactive 2009 Ford Taurus fastener lookup with per-bolt filtering, part links, and torque tools…