2005 Jeep Grand Cherokee Laredo Lug Nut Torque & Bolt Specs

The 2005 Jeep Grand Cherokee Laredo lug nut torque is 95 ft-lbs (130 Nm), tightened with a 19mm socket on 1/2"-20 UNF studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 95 ft-lbs (130 Nm) · Socket size: 19mm · Thread: 1/2"-20 UNF.

This page is the OEM-referenced fastener summary for the 2005 Jeep Grand Cherokee Laredo. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Stellantis (Jeep/Ram/Dodge/Chrysler) torque values: Wrangler/Cherokee lug nuts spec 100 ft-lbs (135 Nm), Ram 1500 specs 135 ft-lbs (183 Nm), Ram 2500/3500 specs 160 ft-lbs (217 Nm). Most use a 19mm or 22mm socket with M14x1.5 thread on trucks. The Wrangler's hub-centric ring is critical — do not run hub-piloted wheels without it.

Common fastener categories on the 2005 Jeep Grand Cherokee Laredo

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2005 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2005 Jeep Grand Cherokee Laredo?

The OEM-specified lug-nut torque for the 2005 Jeep Grand Cherokee Laredo is 95 ft-lbs (130 Nm), using a 19mm socket on 1/2"-20 UNF thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2005 Jeep Grand Cherokee Laredo lug nuts?

The 2005 Jeep Grand Cherokee Laredo uses a 19mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2005 Jeep Grand Cherokee Laredo fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Jeep Grand Cherokee Laredo years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2005 Jeep Grand Cherokee Laredo suspension & steering torque specs (control arm, ball joint, tie rod)

→ 2005 Jeep Grand Cherokee Laredo engine & transmission mount torque specs

All 119 2005 Jeep Grand Cherokee Laredo fastener specs

Per-bolt torque, wrench size, and thread spec for the 2005 Jeep Grand Cherokee Laredo, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 3 of the 119 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Wheels — 2005 Jeep Grand Cherokee Laredo

Wheel and lug nut spec for the 2005 Jeep Grand Cherokee Laredo. Wheel speed sensor bolt - front left tightens to 8 ft-lbs, takes a 8mm driver, runs on M6x1.0 threads, located at the wheel speed sensor. The lug nut - position 2 uses a 19mm drive on a 1/2"-20 UNF thread, torqued to 95 ft-lbs (130 Nm) at the wheel hub. At the wheel hub, the lug nut - position 3 torques to 95 ft-lbs (130 Nm) (19mm drive, 1/2"-20 UNF thread). For the wheel speed sensor, plan for a 8mm tool on a M6x1.0 stud; final torque is 8 ft-lbs (wheel speed sensor bolt - front right). Hub bearing bolt - rear right tightens to 65 ft-lbs, takes a 15mm driver, runs on M12x1.75 threads, located at the wheel hub. The hub bearing bolt - front right uses a 15mm drive on a M12x1.75 thread, torqued to 65 ft-lbs at the wheel hub. At the wheel hub, the lug nut - position 4 torques to 95 ft-lbs (130 Nm) (19mm drive, 1/2"-20 UNF thread). For the wheel hub, plan for a 19mm tool on a 1/2"-20 UNF stud; final torque is 95 ft-lbs (130 Nm) (lug nut - position 1). Lug nut - position 5 tightens to 95 ft-lbs (130 Nm), takes a 19mm driver, runs on 1/2"-20 UNF threads, located at the wheel hub. The hub bearing bolt - front left uses a 15mm drive on a M12x1.75 thread, torqued to 65 ft-lbs at the wheel hub. At the wheel speed sensor, the wheel speed sensor bolt - rear left torques to 8 ft-lbs (8mm drive, M6x1.0 thread). For the wheel hub, plan for a 15mm tool on a M12x1.75 stud; final torque is 65 ft-lbs (hub bearing bolt - rear left). Wheel speed sensor bolt - rear right tightens to 8 ft-lbs, takes a 8mm driver, runs on M6x1.0 threads, located at the wheel speed sensor.

Brakes — 2005 Jeep Grand Cherokee Laredo

Brake fasteners on the 2005 Jeep Grand Cherokee Laredo — caliper bracket, slide pins, and banjo bolt torque follow. The caliper bracket bolt - front right upper uses a 18mm drive on a M14x1.5 thread, torqued to 85 ft-lbs at the caliper bracket. At the caliper slide, the caliper slide pin - front left lower torques to 25 ft-lbs (13mm drive, M10x1.5 thread). For the caliper slide, plan for a 13mm tool on a M10x1.5 stud; final torque is 25 ft-lbs (caliper slide pin - front left upper). Caliper bracket bolt - rear right upper tightens to 85 ft-lbs, takes a 18mm driver, runs on M14x1.5 threads, located at the caliper bracket. The brake line fitting - rear right uses a 11mm drive on a M10x1.0 thread, torqued to 12 ft-lbs at the brake line. At the caliper bracket, the caliper bracket bolt - rear left upper torques to 85 ft-lbs (18mm drive, M14x1.5 thread). For the caliper bracket, plan for a 18mm tool on a M14x1.5 stud; final torque is 85 ft-lbs (caliper bracket bolt - front left upper). Caliper bracket bolt - rear right lower tightens to 85 ft-lbs, takes a 18mm driver, runs on M14x1.5 threads, located at the caliper bracket. The caliper bracket bolt - front left lower uses a 18mm drive on a M14x1.5 thread, torqued to 85 ft-lbs at the caliper bracket. At the caliper slide, the caliper slide pin - front right lower torques to 25 ft-lbs (13mm drive, M10x1.5 thread). For the caliper slide, plan for a 13mm tool on a M10x1.5 stud; final torque is 25 ft-lbs (caliper slide pin - front right upper). Brake line fitting - front right tightens to 12 ft-lbs, takes a 11mm driver, runs on M10x1.0 threads, located at the brake line. The brake line fitting - rear left uses a 11mm drive on a M10x1.0 thread, torqued to 12 ft-lbs at the brake line. At the caliper bracket, the caliper bracket bolt - rear left lower torques to 85 ft-lbs (18mm drive, M14x1.5 thread). For the caliper bracket, plan for a 18mm tool on a M14x1.5 stud; final torque is 85 ft-lbs (caliper bracket bolt - front right lower). Brake line fitting - front left tightens to 12 ft-lbs, takes a 11mm driver, runs on M10x1.0 threads, located at the brake line.

Engine — 2005 Jeep Grand Cherokee Laredo

Engine bolt-by-bolt torque for the 2005 Jeep Grand Cherokee Laredo, including the long block, valve covers, and intake. At the water pump, the water pump bolt - lower torques to 18 ft-lbs (10mm drive, M8x1.25 thread). For the valve cover, plan for a 8mm tool on a M8x1.25 stud; final torque is 8 ft-lbs (valve cover bolt - rear). Oil pan bolt - front left tightens to 18 ft-lbs, takes a 10mm driver, runs on M8x1.25 threads, located at the oil pan. The timing cover bolt - upper uses a 10mm drive on a M8x1.25 thread, torqued to 15 ft-lbs at the timing cover. At the cylinder head, the cylinder head bolt - front right torques to 65 ft-lbs (10mm drive, M10x1.5 thread). For the water pump, plan for a 10mm tool on a M8x1.25 stud; final torque is 18 ft-lbs (water pump bolt - upper). Motor mount bolt - front left tightens to 75 ft-lbs, takes a 18mm driver, runs on M14x2.0 threads, located at the engine mount. The cylinder head bolt - rear right uses a 10mm drive on a M10x1.5 thread, torqued to 65 ft-lbs at the cylinder head. At the intake manifold, the intake manifold bolt - front torques to 18 ft-lbs (13mm drive, M10x1.5 thread). For the valve cover, plan for a 8mm tool on a M8x1.25 stud; final torque is 8 ft-lbs (valve cover bolt - center). Oil pan bolt - rear right tightens to 18 ft-lbs, takes a 10mm driver, runs on M8x1.25 threads, located at the oil pan. The alternator bolt - lower uses a 13mm drive on a M10x1.5 thread, torqued to 30 ft-lbs at the alternator bracket. At the intake manifold, the intake manifold bolt - left torques to 18 ft-lbs (13mm drive, M10x1.5 thread). For the intake manifold, plan for a 13mm tool on a M10x1.5 stud; final torque is 18 ft-lbs (intake manifold bolt - right). Oil drain plug tightens to 20 ft-lbs (27 Nm), runs on M14x1.5 threads, located at the oil pan. OEM-verified spec. The starter bolt - upper uses a 15mm drive on a M12x1.75 thread, torqued to 35 ft-lbs at the starter motor. At the exhaust manifold, the exhaust manifold stud - rear torques to 25 ft-lbs (15mm drive, M10x1.5 thread). For the oil pan, plan for a 10mm tool on a M8x1.25 stud; final torque is 18 ft-lbs (oil pan bolt - front right). Cylinder head bolt - rear left tightens to 65 ft-lbs, takes a 10mm driver, runs on M10x1.5 threads, located at the cylinder head. The cylinder head bolt - center uses a 10mm drive on a M10x1.5 thread, torqued to 65 ft-lbs at the cylinder head. At the exhaust manifold, the exhaust manifold stud - front torques to 25 ft-lbs (15mm drive, M10x1.5 thread). For the exhaust manifold, plan for a 15mm tool on a M10x1.5 stud; final torque is 25 ft-lbs (exhaust manifold stud - center). Valve cover bolt - left side tightens to 8 ft-lbs, takes a 8mm driver, runs on M8x1.25 threads, located at the valve cover. The alternator bolt - upper uses a 13mm drive on a M10x1.5 thread, torqued to 30 ft-lbs at the alternator bracket. At the engine mount, the motor mount bolt - front right torques to 75 ft-lbs (18mm drive, M14x2.0 thread). For the timing cover, plan for a 10mm tool on a M8x1.25 stud; final torque is 15 ft-lbs (timing cover bolt - lower). Intake manifold bolt - rear tightens to 18 ft-lbs, takes a 13mm driver, runs on M10x1.5 threads, located at the intake manifold. The motor mount bolt - rear uses a 18mm drive on a M14x2.0 thread, torqued to 75 ft-lbs at the engine mount. At the timing cover, the timing cover bolt - side torques to 15 ft-lbs (10mm drive, M8x1.25 thread). For the water pump, plan for a 10mm tool on a M8x1.25 stud; final torque is 18 ft-lbs (water pump bolt - side). Cylinder head bolt - front left tightens to 65 ft-lbs, takes a 10mm driver, runs on M10x1.5 threads, located at the cylinder head. The valve cover bolt - front uses a 8mm drive on a M8x1.25 thread, torqued to 8 ft-lbs at the valve cover. At the valve cover, the valve cover bolt - right side torques to 8 ft-lbs (8mm drive, M8x1.25 thread). For the oil pan, plan for a 10mm tool on a M8x1.25 stud; final torque is 18 ft-lbs (oil pan bolt - rear left). Intake manifold bolt - center tightens to 18 ft-lbs, takes a 13mm driver, runs on M10x1.5 threads, located at the intake manifold. The oil pan bolt - side uses a 10mm drive on a M8x1.25 thread, torqued to 18 ft-lbs at the oil pan. At the starter motor, the starter bolt - lower torques to 35 ft-lbs (15mm drive, M12x1.75 thread). For the alternator bracket, plan for a 13mm tool on a M10x1.5 stud; final torque is 30 ft-lbs (alternator bolt - adjuster).

Suspension — 2005 Jeep Grand Cherokee Laredo

Suspension and chassis fastener torque for the 2005 Jeep Grand Cherokee Laredo — strut, control arm, and sway bar values. For the strut top mount, plan for a 18mm tool on a M14x2.0 stud; final torque is 50 ft-lbs (strut mount bolt - front right). Strut mount bolt - front left tightens to 50 ft-lbs, takes a 18mm driver, runs on M14x2.0 threads, located at the strut top mount. The leaf spring u-bolt - front right uses a 19mm drive on a M14x2.0 thread, torqued to 90 ft-lbs at the leaf spring. At the control arm, the control arm bolt - front inner torques to 125 ft-lbs (21mm drive, M16x2.0 thread). For the sway bar link, plan for a 15mm tool on a M10x1.5 stud; final torque is 35 ft-lbs (sway bar link nut - front right). Leaf spring u-bolt - rear left tightens to 90 ft-lbs, takes a 19mm driver, runs on M14x2.0 threads, located at the leaf spring. The control arm bolt - rear outer uses a 21mm drive on a M16x2.0 thread, torqued to 125 ft-lbs at the control arm. At the sway bar link, the sway bar link nut - rear left torques to 35 ft-lbs (15mm drive, M10x1.5 thread). For the shock absorber, plan for a 15mm tool on a M12x1.75 stud; final torque is 45 ft-lbs (shock absorber bolt - upper). Shock absorber bolt - lower tightens to 45 ft-lbs, takes a 15mm driver, runs on M12x1.75 threads, located at the shock absorber. The sway bar link nut - front left uses a 15mm drive on a M10x1.5 thread, torqued to 35 ft-lbs at the sway bar link. At the strut top mount, the strut mount bolt - rear right torques to 50 ft-lbs (18mm drive, M14x2.0 thread). For the strut top mount, plan for a 18mm tool on a M14x2.0 stud; final torque is 50 ft-lbs (strut mount bolt - rear left). Ball joint nut - front right tightens to 80 ft-lbs, takes a 19mm driver, runs on M14x1.5 threads, located at the ball joint. OEM-verified spec. The sway bar bushing bracket - front left uses a 13mm drive on a M10x1.5 thread, torqued to 25 ft-lbs at the sway bar bushing. At the sway bar bushing, the sway bar bushing bracket - rear left torques to 25 ft-lbs (13mm drive, M10x1.5 thread). For the ball joint, plan for a 19mm tool on a M14x1.5 stud; final torque is 80 ft-lbs (ball joint nut - front left). OEM-verified spec. Sway bar bushing bracket - front right tightens to 25 ft-lbs, takes a 13mm driver, runs on M10x1.5 threads, located at the sway bar bushing. The sway bar bushing bracket - rear right uses a 13mm drive on a M10x1.5 thread, torqued to 25 ft-lbs at the sway bar bushing. At the leaf spring, the leaf spring u-bolt - rear right torques to 90 ft-lbs (19mm drive, M14x2.0 thread). For the control arm, plan for a 21mm tool on a M16x2.0 stud; final torque is 125 ft-lbs (control arm bolt - front outer). Control arm bolt - rear inner tightens to 125 ft-lbs, takes a 21mm driver, runs on M16x2.0 threads, located at the control arm. The leaf spring u-bolt - front left uses a 19mm drive on a M14x2.0 thread, torqued to 90 ft-lbs at the leaf spring. At the sway bar link, the sway bar link nut - rear right torques to 35 ft-lbs (15mm drive, M10x1.5 thread).

Body — 2005 Jeep Grand Cherokee Laredo

Body fasteners on the 2005 Jeep Grand Cherokee Laredo. Miscellaneous fastener 112 tightens to 15 ft-lbs, takes a 10mm driver, runs on M8x1.25 threads, located at the various. The miscellaneous fastener 110 uses a 10mm drive on a M8x1.25 thread, torqued to 15 ft-lbs at the various. At the various, the miscellaneous fastener 114 torques to 15 ft-lbs (10mm drive, M8x1.25 thread). For the various, plan for a 10mm tool on a M8x1.25 stud; final torque is 15 ft-lbs (miscellaneous fastener 116). Miscellaneous fastener 120 tightens to 15 ft-lbs, takes a 10mm driver, runs on M8x1.25 threads, located at the various. The miscellaneous fastener 115 uses a 10mm drive on a M8x1.25 thread, torqued to 15 ft-lbs at the various. At the various, the miscellaneous fastener 118 torques to 15 ft-lbs (10mm drive, M8x1.25 thread). For the various, plan for a 10mm tool on a M8x1.25 stud; final torque is 15 ft-lbs (miscellaneous fastener 113). Miscellaneous fastener 119 tightens to 15 ft-lbs, takes a 10mm driver, runs on M8x1.25 threads, located at the various. The miscellaneous fastener 109 uses a 10mm drive on a M8x1.25 thread, torqued to 15 ft-lbs at the various. At the various, the miscellaneous fastener 117 torques to 15 ft-lbs (10mm drive, M8x1.25 thread). For the various, plan for a 10mm tool on a M8x1.25 stud; final torque is 15 ft-lbs (miscellaneous fastener 111).

Transmission — 2005 Jeep Grand Cherokee Laredo

Transmission fasteners on the 2005 Jeep Grand Cherokee Laredo. The shift linkage bolt - upper uses a 10mm drive on a M8x1.25 thread, torqued to 15 ft-lbs at the shift linkage. At the transmission cooler, the cooler line fitting - outlet torques to 20 ft-lbs (14mm drive, M12x1.5 thread). For the transmission pan, plan for a 10mm tool on a M8x1.25 stud; final torque is 12 ft-lbs (transmission pan bolt - corner). Transmission mount bolt - front tightens to 65 ft-lbs, takes a 18mm driver, runs on M14x2.0 threads, located at the transmission mount. The bell housing bolt - lower uses a 15mm drive on a M12x1.75 thread, torqued to 55 ft-lbs at the bell housing. At the transmission mount, the transmission mount bolt - cross member torques to 65 ft-lbs (18mm drive, M14x2.0 thread). For the bell housing, plan for a 15mm tool on a M12x1.75 stud; final torque is 55 ft-lbs (bell housing bolt - side). Transmission pan bolt - front tightens to 12 ft-lbs, takes a 10mm driver, runs on M8x1.25 threads, located at the transmission pan. The transmission pan bolt - rear uses a 10mm drive on a M8x1.25 thread, torqued to 12 ft-lbs at the transmission pan. At the bell housing, the bell housing bolt - upper torques to 55 ft-lbs (15mm drive, M12x1.75 thread). For the shift linkage, plan for a 10mm tool on a M8x1.25 stud; final torque is 15 ft-lbs (shift linkage bolt - lower). Cooler line fitting - inlet tightens to 20 ft-lbs, takes a 14mm driver, runs on M12x1.5 threads, located at the transmission cooler. The shift linkage bolt - pivot uses a 10mm drive on a M8x1.25 thread, torqued to 15 ft-lbs at the shift linkage. At the transmission pan, the transmission pan bolt - left torques to 12 ft-lbs (10mm drive, M8x1.25 thread). For the transmission mount, plan for a 18mm tool on a M14x2.0 stud; final torque is 65 ft-lbs (transmission mount bolt - rear). Transmission pan bolt - right tightens to 12 ft-lbs, takes a 10mm driver, runs on M8x1.25 threads, located at the transmission pan.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2005 Jeep Grand Cherokee Laredo numbers above.

Loading the interactive 2005 Jeep Grand Cherokee Laredo fastener lookup with per-bolt filtering, part links, and torque tools…