2024 Kia K5 Lug Nut Torque & Bolt Specs

The 2024 Kia K5 lug nut torque is 87 ft-lbs, tightened with a 21mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 87 ft-lbs · Socket size: 21mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2024 Kia K5. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Hyundai/Kia lug-nut torque is 79-88 ft-lbs on nearly all passenger models, M12x1.5 thread, 21mm socket. The Tucson, Sportage, and Santa Fe all use the same fastener spec. Hyundai's oil drain plug threads are unusually fine-pitch and strip easily — always use a torque wrench, not feel.

Common fastener categories on the 2024 Kia K5

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2024 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2024 Kia K5?

The OEM-specified lug-nut torque for the 2024 Kia K5 is 87 ft-lbs, using a 21mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2024 Kia K5 lug nuts?

The 2024 Kia K5 uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2024 Kia K5 fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Kia K5 years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2024 Kia K5 suspension & steering torque specs (control arm, ball joint, tie rod)

All 20 2024 Kia K5 fastener specs

Per-bolt torque, wrench size, and thread spec for the 2024 Kia K5, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 2024 Kia K5

Wheel and lug nut spec for the 2024 Kia K5. For the wheel hub, plan for a 21mm tool on a M12x1.5 stud; final torque is 87 ft-lbs (wheel lug nut). Lug nut tightens to 80 ft-lbs (108 Nm), takes a 21mm driver, runs on M12x1.5 threads, located at the all four wheels.

Brakes — 2024 Kia K5

Brake fasteners on the 2024 Kia K5 — caliper bracket, slide pins, and banjo bolt torque follow. Front brake caliper bracket bolt tightens to 65 ft-lbs, takes a 17mm driver, runs on M12x1.5 threads, located at the caliper bracket. The abs wheel speed sensor bolt uses a 10mm drive on a M6x1.0 thread, torqued to 8 ft-lbs at the wheel speed sensor. At the caliper slide, the rear brake caliper slide pin bolt torques to 16 ft-lbs (12mm drive, M8x1.25 thread). For the caliper slide, plan for a 14mm tool on a M10x1.25 stud; final torque is 27 ft-lbs (front brake caliper slide pin bolt). Rear brake caliper bracket bolt tightens to 41 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the caliper bracket.

Engine — 2024 Kia K5

Engine bolt-by-bolt torque for the 2024 Kia K5, including the long block, valve covers, and intake. The oil pan drain plug uses a 17mm drive on a M14x1.5 thread, torqued to 29 ft-lbs at the oil pan. At the intake manifold, the intake manifold bolt torques to 19 ft-lbs (12mm drive, M8x1.25 thread). For the valve cover, plan for a 10mm tool on a M6x1.0 stud; final torque is 6 ft-lbs (valve cover bolt). Exhaust manifold bolt tightens to 25 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the exhaust manifold. The cylinder head bolt uses a 12mm drive on a M10x1.25 thread, torqued to 19 ft-lbs at the cylinder head.

Suspension — 2024 Kia K5

Suspension and chassis fastener torque for the 2024 Kia K5 — strut, control arm, and sway bar values. At the strut top mount, the front strut top mount bolt torques to 45 ft-lbs (19mm drive, M14x1.5 thread). For the knuckle, plan for a 19mm tool on a M14x1.5 stud; final torque is 75 ft-lbs (steering knuckle bolt). Front ball joint nut tightens to 49 ft-lbs, takes a 19mm driver, runs on M14x1.5 threads, located at the ball joint. The front lower control arm bolt uses a 22mm drive on a M16x1.5 thread, torqued to 65 ft-lbs at the control arm. At the sway bar link, the sway bar link nut torques to 23 ft-lbs (14mm drive, M10x1.25 thread). For the knuckle, plan for a 17mm tool on a M12x1.25 stud; final torque is 32 ft-lbs (tie rod end nut).

Transmission — 2024 Kia K5

Transmission fasteners on the 2024 Kia K5. For the transmission mount, plan for a 14mm tool on a M10x1.25 stud; final torque is 44 ft-lbs (transmission mount bolt). Bell housing bolt tightens to 58 ft-lbs, takes a 17mm driver, runs on M12x1.5 threads, located at the bell housing.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2024 Kia K5 numbers above.

Loading the interactive 2024 Kia K5 fastener lookup with per-bolt filtering, part links, and torque tools…