2013 Kia Rio5 Lug Nut Torque & Bolt Specs

The 2013 Kia Rio5 lug nut torque is 80 ft-lbs (108 Nm), tightened with a 21mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 21mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2013 Kia Rio5. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Hyundai/Kia lug-nut torque is 79-88 ft-lbs on nearly all passenger models, M12x1.5 thread, 21mm socket. The Tucson, Sportage, and Santa Fe all use the same fastener spec. Hyundai's oil drain plug threads are unusually fine-pitch and strip easily — always use a torque wrench, not feel.

Common fastener categories on the 2013 Kia Rio5

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2013 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2013 Kia Rio5?

The OEM-specified lug-nut torque for the 2013 Kia Rio5 is 80 ft-lbs (108 Nm), using a 21mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2013 Kia Rio5 lug nuts?

The 2013 Kia Rio5 uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2013 Kia Rio5 fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Kia Rio5 years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2013 Kia Rio5 oil drain plug torque & size

→ 2013 Kia Rio5 suspension & steering torque specs (control arm, ball joint, tie rod)

→ 2013 Kia Rio5 axle nut torque spec (CV axle & hub nut)

All 33 2013 Kia Rio5 fastener specs

Per-bolt torque, wrench size, and thread spec for the 2013 Kia Rio5, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 2 of the 33 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data.

Wheels — 2013 Kia Rio5

Wheel and lug nut spec for the 2013 Kia Rio5. Lug nut tightens to 80 ft-lbs (108 Nm), takes a 21mm driver, runs on M12x1.5 threads, located at the all four wheels. The wheel lug nut uses a 19mm drive on a M12x1.5 thread, torqued to 81 ft-lbs at the wheel hub.

Brakes — 2013 Kia Rio5

Brake fasteners on the 2013 Kia Rio5 — caliper bracket, slide pins, and banjo bolt torque follow. The front brake caliper slide pin bolt uses a 12mm drive on a M8x1.25 thread, torqued to 20 ft-lbs at the caliper slide. At the rear hub, the rear drum backing plate bolt torques to 36 ft-lbs (12mm drive, M8x1.25 thread).

Engine — 2013 Kia Rio5

Engine bolt-by-bolt torque for the 2013 Kia Rio5, including the long block, valve covers, and intake. At the cylinder head, the spark plug torques to 13-17 ft-lbs (16mm Hex drive, M14x1.25 thread). For the engine block, plan for a 14mm Hex tool on a M10x1.25 stud; final torque is 30-40 ft-lbs (alternator mounting bolt). Valve cover bolt tightens to 7-10 ft-lbs, takes a 10mm Hex driver, runs on M6x1.0 threads, located at the valve cover. The oil pan drain plug uses a 17mm drive on a M14x1.5 thread, torqued to 25 ft-lbs at the oil pan. At the cylinder head, the cylinder head bolt torques to 22 ft-lbs + 90 + 90 deg (12mm drive, M10x1.25 thread). For the oil pan, plan for a 17mm Hex tool on a M14x1.5 stud; final torque is 25 ft-lbs (34 Nm) (oil drain plug). Intake manifold bolt tightens to 15 ft-lbs, takes a 12mm driver, runs on M8x1.25 threads, located at the intake manifold.

Drivetrain — 2013 Kia Rio5

Drivetrain and driveline fasteners for the 2013 Kia Rio5 — axle, transmission, and differential plugs. For the center support bearing, plan for a 14mm Hex tool on a M10x1.25 stud; final torque is 30-40 ft-lbs (driveshaft center support bolt). Axle nut rear tightens to 170-200 ft-lbs, takes a 32mm Hex driver, runs on M24x1.5 threads, located at the rear hub. The transmission mount bolt uses a 17mm Hex drive on a M12x1.25 thread, torqued to 55-70 ft-lbs at the transmission crossmember. At the front hub, the axle nut front torques to 170-200 ft-lbs (32mm Hex drive, M24x1.5 thread).

Suspension — 2013 Kia Rio5

Suspension and chassis fastener torque for the 2013 Kia Rio5 — strut, control arm, and sway bar values. Front lower control arm front bolt tightens to 70-85 ft-lbs, takes a 17mm Hex driver, runs on M12x1.25 threads, located at the front subframe. The front lower control arm rear bolt uses a 17mm Hex drive on a M12x1.25 thread, torqued to 70-85 ft-lbs at the rear subframe mount. At the strut top mount, the front strut mount bolt torques to 40 ft-lbs (17mm drive, M12x1.5 thread). For the strut tower, plan for a 21mm Hex tool on a M14x1.5 stud; final torque is 30-40 ft-lbs (front strut top mount nut). Stabilizer bar link nut front tightens to 25-35 ft-lbs, takes a 14mm Hex driver, runs on M10x1.25 threads, located at the sway bar end link. The sway bar link nut uses a 12mm drive on a M8x1.25 thread, torqued to 29 ft-lbs at the sway bar link. At the shock tower, the rear shock absorber upper nut torques to 35-45 ft-lbs (17mm Hex drive, M12x1.25 thread). For the rear knuckle, plan for a 21mm Hex tool on a M14x1.5 stud; final torque is 85-100 ft-lbs (rear shock absorber lower bolt). Front control arm bolt tightens to 51 ft-lbs, takes a 17mm driver, runs on M12x1.5 threads, located at the control arm. The front ball joint nut uses a 14mm drive on a M10x1.25 thread, torqued to 37 ft-lbs at the ball joint.

Steering — 2013 Kia Rio5

Steering linkage fasteners on the 2013 Kia Rio5. The tie rod end nut uses a 17mm Castle drive on a M12x1.25 thread, torqued to 25-33 ft-lbs at the steering knuckle. At the steering column, the steering wheel center bolt torques to 30-38 ft-lbs (24mm Hex drive, M16x1.5 thread).

Body — 2013 Kia Rio5

Body fasteners on the 2013 Kia Rio5. At the hood hinge, the hood hinge bolt torques to 15-20 ft-lbs (12mm Hex drive, M8x1.25 thread).

Brake — 2013 Kia Rio5

Brake fasteners on the 2013 Kia Rio5. For the caliper bracket, plan for a 14mm Hex tool on a M10x1.25 stud; final torque is 20-28 ft-lbs (rear brake caliper guide pin bolt). OEM-verified spec. Front brake caliper bracket bolt tightens to 55-70 ft-lbs, takes a 17mm Hex driver, runs on M12x1.25 threads, located at the front knuckle. The rear brake caliper bracket bolt uses a 17mm Hex drive on a M12x1.25 thread, torqued to 50-65 ft-lbs at the rear knuckle. At the caliper bracket, the front brake caliper guide pin bolt torques to 22-30 ft-lbs (14mm Hex drive, M10x1.25 thread). OEM-verified spec.

Wheel — 2013 Kia Rio5

Wheel fasteners on the 2013 Kia Rio5. Wheel lug nuts tightens to 80 ft-lbs (108 Nm), takes a 19mm Hex driver, runs on M12x1.5 threads, located at the wheel hub.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2013 Kia Rio5 numbers above.

Loading the interactive 2013 Kia Rio5 fastener lookup with per-bolt filtering, part links, and torque tools…