2017 Kia Sportage Lug Nut Torque & Bolt Specs

The 2017 Kia Sportage lug nut torque is 80 ft-lbs (108 Nm), tightened with a 19mm Hex socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 19mm Hex · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2017 Kia Sportage. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Hyundai/Kia lug-nut torque is 79-88 ft-lbs on nearly all passenger models, M12x1.5 thread, 21mm socket. The Tucson, Sportage, and Santa Fe all use the same fastener spec. Hyundai's oil drain plug threads are unusually fine-pitch and strip easily — always use a torque wrench, not feel.

Common fastener categories on the 2017 Kia Sportage

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2017 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2017 Kia Sportage?

The OEM-specified lug-nut torque for the 2017 Kia Sportage is 80 ft-lbs (108 Nm), using a 19mm Hex socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2017 Kia Sportage lug nuts?

The 2017 Kia Sportage uses a 19mm Hex socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2017 Kia Sportage fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Kia Sportage years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2017 Kia Sportage oil drain plug torque & size

→ 2017 Kia Sportage suspension & steering torque specs (control arm, ball joint, tie rod)

→ 2017 Kia Sportage axle nut torque spec (CV axle & hub nut)

All 36 2017 Kia Sportage fastener specs

Per-bolt torque, wrench size, and thread spec for the 2017 Kia Sportage, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 3 of the 36 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data.

Wheels — 2017 Kia Sportage

Wheel and lug nut spec for the 2017 Kia Sportage. Lug nut tightens to 80 ft-lbs (108 Nm), takes a 21mm driver, runs on M12x1.5 threads, located at the all four wheels.

Engine — 2017 Kia Sportage

Engine bolt-by-bolt torque for the 2017 Kia Sportage, including the long block, valve covers, and intake. The valve cover bolt uses a 10mm Hex drive on a M6x1.0 thread, torqued to 7-10 ft-lbs at the valve cover. At the engine block, the alternator mounting bolt torques to 30-40 ft-lbs (14mm Hex drive, M10x1.25 thread). For the oil pan, plan for a 17mm tool on a M14x1.5 stud; final torque is 25 ft-lbs (34 Nm) (oil drain plug). Spark plug tightens to 13-17 ft-lbs, takes a 16mm Hex driver, runs on M14x1.25 threads, located at the cylinder head. The oil filter uses a 76mm drive on a 3/4-16 UNF thread, torqued to 15 Nm at the engine block. Confirmed against manufacturer service literature.

Drivetrain — 2017 Kia Sportage

Drivetrain and driveline fasteners for the 2017 Kia Sportage — axle, transmission, and differential plugs. At the center support bearing, the driveshaft center support bolt torques to 30-40 ft-lbs (14mm Hex drive, M10x1.25 thread). For the front hub, plan for a 32mm Hex tool on a M24x1.5 stud; final torque is 170-200 ft-lbs (axle nut front). Axle nut rear tightens to 170-200 ft-lbs, takes a 32mm Hex driver, runs on M24x1.5 threads, located at the rear hub. The transmission mount bolt uses a 17mm Hex drive on a M12x1.25 thread, torqued to 55-70 ft-lbs at the transmission crossmember.

Suspension — 2017 Kia Sportage

Suspension and chassis fastener torque for the 2017 Kia Sportage — strut, control arm, and sway bar values. For the strut tower, plan for a 21mm Hex tool on a M14x1.5 stud; final torque is 30-40 ft-lbs (front strut top mount nut). Front lower control arm front bolt tightens to 70-85 ft-lbs, takes a 17mm Hex driver, runs on M12x1.25 threads, located at the front subframe. The stabilizer bar link nut front uses a 14mm Hex drive on a M10x1.25 thread, torqued to 25-35 ft-lbs at the sway bar end link. At the rear axle, the rear shock lower bolt torques to 118 Nm (17mm drive, M12x1.5 thread). For the rear subframe mount, plan for a 17mm Hex tool on a M12x1.25 stud; final torque is 70-85 ft-lbs (front lower control arm rear bolt). Front strut upper nut tightens to 50 Nm, takes a 17mm driver, runs on M12x1.5 threads, located at the strut tower. The rear shock absorber upper nut uses a 17mm Hex drive on a M12x1.25 thread, torqued to 35-45 ft-lbs at the shock tower. At the subframe, the front lower control arm torques to 137 Nm (19mm drive, M14x1.5 thread). For the knuckle, plan for a 19mm tool on a M14x1.5 stud; final torque is 50 Nm (front tie rod end nut). Rear shock absorber lower bolt tightens to 85-100 ft-lbs, takes a 21mm Hex driver, runs on M14x1.5 threads, located at the rear knuckle. The front strut lower bolt uses a 18mm drive on a M14x1.5 thread, torqued to 190 Nm at the knuckle.

Steering — 2017 Kia Sportage

Steering linkage fasteners on the 2017 Kia Sportage. Tie rod end nut tightens to 25-33 ft-lbs, takes a 17mm Castle driver, runs on M12x1.25 threads, located at the steering knuckle. The steering wheel center bolt uses a 24mm Hex drive on a M16x1.5 thread, torqued to 30-38 ft-lbs at the steering column.

Body — 2017 Kia Sportage

Body fasteners on the 2017 Kia Sportage. The hood hinge bolt uses a 12mm Hex drive on a M8x1.25 thread, torqued to 15-20 ft-lbs at the hood hinge.

Wheel — 2017 Kia Sportage

Wheel fasteners on the 2017 Kia Sportage. At the front/rear, the wheel lug nut torques to 80 ft-lbs (108 Nm) (21mm drive, M12x1.5 thread). For the front, plan for a 32mm tool on a M24x1.5 stud; final torque is 240 Nm (front axle nut). Wheel lug nuts tightens to 80 ft-lbs (108 Nm), takes a 19mm Hex driver, runs on M12x1.5 threads, located at the wheel hub. The rear axle nut uses a 32mm drive on a M24x1.5 thread, torqued to 240 Nm at the rear.

Brake — 2017 Kia Sportage

Brake fasteners on the 2017 Kia Sportage. For the caliper bracket, plan for a 14mm Hex tool on a M10x1.25 stud; final torque is 22-30 ft-lbs (front brake caliper guide pin bolt). OEM-verified spec. Rear brake caliper bracket bolt tightens to 50-65 ft-lbs, takes a 17mm Hex driver, runs on M12x1.25 threads, located at the rear knuckle. The front brake caliper bolt uses a 17mm drive on a M12x1.5 thread, torqued to 34 Nm at the front caliper. At the front hub, the front brake caliper bracket torques to 95 Nm (17mm drive, M14x1.5 thread). For the rear hub, plan for a 17mm tool on a M14x1.5 stud; final torque is 69 Nm (rear brake caliper bracket). Rear brake caliper guide pin bolt tightens to 20-28 ft-lbs, takes a 14mm Hex driver, runs on M10x1.25 threads, located at the caliper bracket. This figure is independently verified against OEM service data. The front brake caliper bracket bolt uses a 17mm Hex drive on a M12x1.25 thread, torqued to 55-70 ft-lbs at the front knuckle. At the rear caliper, the rear brake caliper bolt torques to 23 Nm (14mm drive, M10x1.25 thread).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2017 Kia Sportage numbers above.

Loading the interactive 2017 Kia Sportage fastener lookup with per-bolt filtering, part links, and torque tools…