2023 Lincoln Nautilus Lug Nut Torque & Bolt Specs

The 2023 Lincoln Nautilus lug nut torque is 100 ft-lbs (136 Nm), tightened with a 19mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 100 ft-lbs (136 Nm) · Socket size: 19mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2023 Lincoln Nautilus. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 2023 Lincoln Nautilus, fasteners follow metric standards typical of late-model Lincoln engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 2023 Lincoln Nautilus

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2023 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2023 Lincoln Nautilus?

The OEM-specified lug-nut torque for the 2023 Lincoln Nautilus is 100 ft-lbs (136 Nm), using a 19mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2023 Lincoln Nautilus lug nuts?

The 2023 Lincoln Nautilus uses a 19mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2023 Lincoln Nautilus fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Lincoln Nautilus years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2023 Lincoln Nautilus oil drain plug torque & size

→ 2023 Lincoln Nautilus suspension & steering torque specs (control arm, ball joint, tie rod)

All 12 2023 Lincoln Nautilus fastener specs

Per-bolt torque, wrench size, and thread spec for the 2023 Lincoln Nautilus, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Brakes — 2023 Lincoln Nautilus

Brake fasteners on the 2023 Lincoln Nautilus — caliper bracket, slide pins, and banjo bolt torque follow. The front caliper slide pin uses a 13mm drive on a M8x1.25 thread, torqued to 26 ft-lbs (35 Nm) at the front. At the front, the front caliper bracket bolt torques to 111 ft-lbs (150 Nm) (18mm drive, M12x1.75 thread). For the rear, plan for a 13mm tool on a M8x1.25 stud; final torque is 26 ft-lbs (35 Nm) (rear caliper slide pin). Rear caliper bracket bolt tightens to 52 ft-lbs (70 Nm), takes a 15mm driver, runs on M10x1.5 threads, located at the rear.

Engine — 2023 Lincoln Nautilus

Engine bolt-by-bolt torque for the 2023 Lincoln Nautilus, including the long block, valve covers, and intake. The oil drain plug torques to 20 ft-lbs (27 Nm) (15mm drive, M14x1.5 thread). plan for a 1-1/16 in. tool; final torque is 18 ft-lbs (25 Nm) (oil filter). Spark plug tightens to 13 ft-lbs (18 Nm), takes a 9/16 in. driver, runs on M14x1.25 threads.

Suspension — 2023 Lincoln Nautilus

Suspension and chassis fastener torque for the 2023 Lincoln Nautilus — strut, control arm, and sway bar values. For the front, plan for a 15mm tool on a M12x1.5 stud; final torque is 37 ft-lbs (50 Nm) (front strut top nut). Front lower control arm bolt tightens to 74 ft-lbs (100 Nm), takes a 18mm driver, runs on M12x1.5 threads, located at the front. The rear lower control arm bolt uses a 15mm drive on a M10x1.5 thread, torqued to 59 ft-lbs (80 Nm) at the rear.

Wheels & Tires — 2023 Lincoln Nautilus

Wheels & Tires fasteners on the 2023 Lincoln Nautilus. Lug nut tightens to 100 ft-lbs (136 Nm), takes a 19mm driver, runs on M12x1.5 threads.

Transmission — 2023 Lincoln Nautilus

Transmission fasteners on the 2023 Lincoln Nautilus. The transmission drain plug uses a 10mm hex drive on a M14x1.5 thread, torqued to 18 ft-lbs (25 Nm).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2023 Lincoln Nautilus numbers above.

Loading the interactive 2023 Lincoln Nautilus fastener lookup with per-bolt filtering, part links, and torque tools…