2014 Mazda CX-5 Lug Nut Torque & Bolt Specs

The 2014 Mazda CX-5 lug nut torque is 90 ft-lbs, tightened with a 21mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 90 ft-lbs · Socket size: 21mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2014 Mazda CX-5. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

For the 2014 Mazda CX-5, fasteners follow metric standards typical of late-model Mazda engineering. Always confirm spec against the factory service manual before tightening safety-critical fasteners (suspension, brake, steering, head bolts).

Common fastener categories on the 2014 Mazda CX-5

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2014 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2014 Mazda CX-5?

The OEM-specified lug-nut torque for the 2014 Mazda CX-5 is 90 ft-lbs, using a 21mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2014 Mazda CX-5 lug nuts?

The 2014 Mazda CX-5 uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2014 Mazda CX-5 fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Mazda CX-5 years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2014 Mazda CX-5 oil drain plug torque & size

→ 2014 Mazda CX-5 suspension & steering torque specs (control arm, ball joint, tie rod)

All 16 2014 Mazda CX-5 fastener specs

Per-bolt torque, wrench size, and thread spec for the 2014 Mazda CX-5, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Brakes — 2014 Mazda CX-5

Brake fasteners on the 2014 Mazda CX-5 — caliper bracket, slide pins, and banjo bolt torque follow. For the rear caliper bracket to knuckle, plan for a 14mm tool on a M10x1.25 stud; final torque is 45 ft-lbs (rear brake caliper bracket bolt). Brake caliper guide pin bolt tightens to 25 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the front caliper to bracket. The brake hose to caliper banjo bolt uses a 12mm drive on a M10x1.0 thread, torqued to 22 ft-lbs at the front & rear calipers. At the front caliper bracket to knuckle, the brake caliper bracket bolt torques to 85 ft-lbs (17mm drive, M12x1.5 thread).

Engine — 2014 Mazda CX-5

Engine bolt-by-bolt torque for the 2014 Mazda CX-5, including the long block, valve covers, and intake. Connecting rod bolt tightens to Stage 1: 18 ft-lbs, Stage 2: +90°, takes a 13mm driver, runs on M9x1.0 threads, located at the engine. The cylinder head bolt uses a 14mm drive on a M11x1.5 thread, torqued to Stage 1: 35 ft-lbs, Stage 2: +90°, Stage 3: +90° at the engine. At the oil pan, the oil drain plug torques to 30 ft-lbs (17mm drive, M14x1.5 thread). For the valve cover perimeter, plan for a 8mm tool on a M6x1.0 stud; final torque is 7 ft-lbs (84 in-lbs) (valve cover bolts). Spark plug tightens to 14 ft-lbs, takes a 14mm Spark Plug Socket driver, runs on M12x1.25 threads, located at the cylinder head. The intake manifold bolts uses a 12mm drive on a M8x1.25 thread, torqued to 18 ft-lbs at the cylinder head.

Suspension — 2014 Mazda CX-5

Suspension and chassis fastener torque for the 2014 Mazda CX-5 — strut, control arm, and sway bar values. The front sway bar end link nuts uses a 14mm drive on a M10x1.25 thread, torqued to 34 ft-lbs at the strut and sway bar. At the upper shock mount, the rear shock absorber top mount bolt torques to 25 ft-lbs (14mm drive, M10x1.25 thread). For the strut tower, plan for a 14mm tool on a M10x1.25 stud; final torque is 35 ft-lbs (front strut top mount nuts). Rear shock absorber lower mount bolt tightens to 75 ft-lbs, takes a 17mm driver, runs on M12x1.5 threads, located at the lower control arm. The front strut to knuckle bolts uses a 19mm drive on a M14x1.5 thread, torqued to 130 ft-lbs at the steering knuckle.

Exterior — 2014 Mazda CX-5

Exterior fasteners on the 2014 Mazda CX-5. At the wheel hub, the wheel lug nut torques to 90 ft-lbs (21mm drive, M12x1.5 thread).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2014 Mazda CX-5 numbers above.

Loading the interactive 2014 Mazda CX-5 fastener lookup with per-bolt filtering, part links, and torque tools…