2024 Nissan Z Lug Nut Torque & Bolt Specs
The 2024 Nissan Z lug nut torque is 80 ft-lbs (108 Nm), tightened with a 19mm socket on M12x1.25 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.
Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 19mm · Thread: M12x1.25.
This page is the OEM-referenced fastener summary for the 2024 Nissan Z. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.
Nissan lug-nut torque is 83 ft-lbs (113 Nm) for nearly every passenger model since 2000 with an M12x1.25 thread (note: tighter pitch than Toyota/Honda's M12x1.5 — the lugs do not cross-thread cleanly with neighboring makes). Socket size is 21mm. Titans and Armadas use a larger M14x1.5 thread at 133 ft-lbs.
Common fastener categories on the 2024 Nissan Z
- Wheel / lug nut torque and thread spec (covered above)
- Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
- Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
- Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
- Suspension control arm, sway bar, tie rod end and ball joint torque
- Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
- Differential cover bolts (RWD/4WD only) and transfer case fasteners
Repair guidance for this model year
For 2024 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.
Tools you will need
- Metric socket set (8mm-22mm), 6-point impact-rated
- Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
- Breaker bar (24" minimum) for initial loosening
- Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
- Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly
Frequently asked questions
What is the lug nut torque on a 2024 Nissan Z?
The OEM-specified lug-nut torque for the 2024 Nissan Z is 80 ft-lbs (108 Nm), using a 19mm socket on M12x1.25 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.
What socket size do I need for the 2024 Nissan Z lug nuts?
The 2024 Nissan Z uses a 19mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.
Are the 2024 Nissan Z fasteners metric or SAE?
Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.
Other Nissan Z years
Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.
→ 2024 Nissan Z oil drain plug torque & size
All 2 2024 Nissan Z fastener specs
Per-bolt torque, wrench size, and thread spec for the 2024 Nissan Z, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 1 of the 2 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).
Wheels — 2024 Nissan Z
Wheel and lug nut spec for the 2024 Nissan Z. At the wheel hub, the wheel lug nut torques to 80 ft-lbs (108 Nm) (19mm drive, M12x1.25 thread).
Engine — 2024 Nissan Z
Engine bolt-by-bolt torque for the 2024 Nissan Z, including the long block, valve covers, and intake. For the oil pan, plan for the right driver on a M12x1.25 stud; final torque is 25 ft-lbs (34 Nm) (oil drain plug). Confirmed against manufacturer service literature.
New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2024 Nissan Z numbers above.
Loading the interactive 2024 Nissan Z fastener lookup with per-bolt filtering, part links, and torque tools…