2024 Subaru Crosstrek Lug Nut Torque & Bolt Specs

The 2024 Subaru Crosstrek lug nut torque is 89 ft-lbs (121 Nm), tightened with a 19mm socket on M12x1.25 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 89 ft-lbs (121 Nm) · Socket size: 19mm · Thread: M12x1.25.

This page is the OEM-referenced fastener summary for the 2024 Subaru Crosstrek. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Subaru lug-nut torque is 89 ft-lbs (120 Nm) on every modern model with an M12x1.25 thread and 19mm socket. Subaru is one of the only Japanese makes still using the smaller 19mm socket — bring it specifically. The boxer engine's drain plug is on the bottom of the block (not the pan) and uses an unusual 17mm head.

Common fastener categories on the 2024 Subaru Crosstrek

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2024 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2024 Subaru Crosstrek?

The OEM-specified lug-nut torque for the 2024 Subaru Crosstrek is 89 ft-lbs (121 Nm), using a 19mm socket on M12x1.25 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2024 Subaru Crosstrek lug nuts?

The 2024 Subaru Crosstrek uses a 19mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2024 Subaru Crosstrek fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Subaru Crosstrek years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2024 Subaru Crosstrek suspension & steering torque specs (control arm, ball joint, tie rod)

All 33 2024 Subaru Crosstrek fastener specs

Per-bolt torque, wrench size, and thread spec for the 2024 Subaru Crosstrek, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 5 of the 33 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Wheels — 2024 Subaru Crosstrek

Wheel and lug nut spec for the 2024 Subaru Crosstrek. At the all corners, the lug nut torques to 89 ft-lbs (121 Nm) (19mm drive, M12x1.25 thread). OEM-verified spec.

Brakes — 2024 Subaru Crosstrek

Brake fasteners on the 2024 Subaru Crosstrek — caliper bracket, slide pins, and banjo bolt torque follow. For the rear caliper bracket to rear knuckle, plan for a 17mm tool on a M10x1.25 stud; final torque is 40 ft-lb (54 Nm) (rear brake caliper bracket bolt). Rear caliper guide pin bolt tightens to 17 ft-lb (23 Nm), takes a 14mm driver, runs on M9x1.25 threads, located at the rear caliper slide pins. The front brake caliper bracket bolt uses a 17mm drive on a M12x1.5 thread, torqued to 89 ft-lbs (121 Nm) at the front caliper bracket to steering knuckle. OEM-verified spec. At the front caliper slide pins (top + bottom), the front caliper guide pin bolt torques to 20 ft-lbs (27 Nm) (14mm drive, M9x1.25 thread). Confirmed against manufacturer service literature. For the brake hose to caliper, plan for a 12mm tool on a M10x1.0 stud; final torque is 22 ft-lb (30 Nm) (brake hose banjo bolt).

Engine — 2024 Subaru Crosstrek

Engine bolt-by-bolt torque for the 2024 Subaru Crosstrek, including the long block, valve covers, and intake. Camshaft cap bolt tightens to 7.2 ft-lb (10 Nm), takes a 10mm driver, runs on M6x1.0 threads, located at the cam carrier / camshaft caps. The engine mount bolt uses a 17mm drive on a M10x1.25 thread, torqued to 40 ft-lb (54 Nm) at the engine mount to subframe (both sides). At the oil pan, the oil drain plug torques to 32 ft-lbs (43 Nm) (17mm drive, M12x1.25 thread). Confirmed against manufacturer service literature. For the valve covers (both banks, 6mm fastener), plan for a 10mm tool on a M6x1.0 stud; final torque is 5.8 ft-lb (8 Nm) (valve cover bolt). Spark plug tightens to 13 ft-lbs (18 Nm), takes a 5/8" (16mm) driver, runs on M12x1.25 threads, located at the cylinder head spark plug well (4 plugs). OEM-verified spec. The crankshaft pulley bolt uses a 22mm drive on a M16x1.5 thread, torqued to Stage 1: 33 ft-lb, Stage 2: 130 ft-lb (177 Nm) at the crankshaft front (timing cover side). At the intake manifold to cylinder head, the intake manifold bolt torques to 16 ft-lb (22 Nm) (12mm drive, M8x1.25 thread). For the oil filter housing / cooler to block, plan for a 12mm tool on a M8x1.25 stud; final torque is 30 ft-lb (40 Nm) (oil filter housing bolt). Cylinder head bolt tightens to Multi-stage TTY: 22 ft-lb, then 51 ft-lb, then loosen 180°+180°, then 22 ft-lb, then 51 ft-lb, then +80° + sequence angles, takes a 14mm driver, runs on M11x1.5 threads, located at the cylinder head (fb25 2.5l boxer).

Drivetrain — 2024 Subaru Crosstrek

Drivetrain and driveline fasteners for the 2024 Subaru Crosstrek — axle, transmission, and differential plugs. The rear differential fill plug uses a 10mm hex drive on a M18x1.5 thread, torqued to 36.9 ft-lb (50 Nm) at the rear differential housing fill. At the cvt fill/level plug on transmission case, the cvt transmission fill plug torques to 36.9 ft-lb (50 Nm) (10mm hex drive, M18x1.5 thread). For the front hub, plan for a 35mm tool on a M24x1.5 stud; final torque is 137 ft-lb (axle nut). Rear differential drain plug tightens to 36.2 ft-lb (49 Nm), takes a 10mm hex driver, runs on M18x1.5 threads, located at the rear differential housing drain. The cvt transmission drain plug uses a 17mm drive on a M14x1.5 thread, torqued to 22.9 ft-lb (31 Nm) at the cvt transmission pan drain plug.

Suspension — 2024 Subaru Crosstrek

Suspension and chassis fastener torque for the 2024 Subaru Crosstrek — strut, control arm, and sway bar values. At the ball joint to steering knuckle pinch, the ball joint pinch bolt torques to 37 ft-lb (50 Nm) (14mm drive, M10x1.25 thread). For the strut lower mount to knuckle (2 bolts), plan for a 19mm tool on a M14x1.5 stud; final torque is 116 ft-lb (157 Nm) (front strut-to-knuckle bolt). Sway bar end link nut tightens to 34 ft-lb (46 Nm), takes a 14mm + T30 driver, runs on M10x1.25 threads, located at the sway bar end link, top and bottom. The tie rod end nut uses a 17mm drive on a M12x1.25 thread, torqued to 29 ft-lb + 60° (40 Nm + 60°) at the tie rod end to steering knuckle. At the front control arm front bushing to chassis, the front lower control arm front bushing bolt torques to 81 ft-lb (110 Nm) (17mm drive, M12x1.25 thread). For the rear strut mount nuts on body, plan for a 14mm tool on a M8x1.25 stud; final torque is 23 ft-lb (31 Nm) (rear strut top hat nut). Front lower control arm rear bushing bolt tightens to 111 ft-lb (150 Nm), takes a 21mm driver, runs on M14x1.5 threads, located at the front control arm rear bushing bracket to chassis. The front strut top hat nut uses a 14mm drive on a M8x1.25 thread, torqued to 15 ft-lb (20 Nm) at the strut mount nuts on top of strut tower (3 nuts). At the rear strut to rear knuckle, the rear lower strut bolt torques to 89 ft-lb (120 Nm) (19mm drive, M12x1.5 thread). For the rear lateral link to chassis and knuckle, plan for a 19mm tool on a M12x1.5 stud; final torque is 89 ft-lb (120 Nm) (rear control arm bolt). Front strut center (upper) nut tightens to 40 ft-lb (54 Nm), takes a 19mm driver, runs on M14x1.5 threads, located at the strut shaft top center nut.

Body — 2024 Subaru Crosstrek

Body fasteners on the 2024 Subaru Crosstrek. For the wilderness roof rails to body, plan for a 12mm tool on a M8x1.25 stud; final torque is 17 ft-lb (23 Nm) (roof rail mount bolt). Skid plate bolt tightens to 14 ft-lb (19 Nm), takes a 14mm driver, runs on M8x1.25 threads, located at the front skid plate to subframe (wilderness only).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2024 Subaru Crosstrek numbers above.

Loading the interactive 2024 Subaru Crosstrek fastener lookup with per-bolt filtering, part links, and torque tools…