2020 Toyota Land Cruiser Lug Nut Torque & Bolt Specs

The 2020 Toyota Land Cruiser lug nut torque is 97 ft-lbs (131 Nm), tightened with a 21mm socket on M14x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 97 ft-lbs (131 Nm) · Socket size: 21mm · Thread: M14x1.5.

This page is the OEM-referenced fastener summary for the 2020 Toyota Land Cruiser. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Toyota's engineering standard for wheel torque is unusually consistent across the lineup — nearly every passenger Toyota from the mid-2000s onward specs 76 ft-lbs (103 Nm) for the lug nuts with an M12x1.5 thread and 21mm socket. The big exceptions are the Tundra and Sequoia full-size trucks (97-110 ft-lbs), and the lug studs on older Camrys and Corollas (pre-2002) used a smaller M12x1.25 thread that does not interchange. Always confirm by checking the alloy stamp on the wheel hub if you are unsure.

Common fastener categories on the 2020 Toyota Land Cruiser

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2020 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2020 Toyota Land Cruiser?

The OEM-specified lug-nut torque for the 2020 Toyota Land Cruiser is 97 ft-lbs (131 Nm), using a 21mm socket on M14x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2020 Toyota Land Cruiser lug nuts?

The 2020 Toyota Land Cruiser uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2020 Toyota Land Cruiser fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Toyota Land Cruiser years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2020 Toyota Land Cruiser oil drain plug torque & size

→ 2020 Toyota Land Cruiser suspension & steering torque specs (control arm, ball joint, tie rod)

All 23 2020 Toyota Land Cruiser fastener specs

Per-bolt torque, wrench size, and thread spec for the 2020 Toyota Land Cruiser, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Brakes — 2020 Toyota Land Cruiser

Brake fasteners on the 2020 Toyota Land Cruiser — caliper bracket, slide pins, and banjo bolt torque follow. The caliper bracket bolt uses a 17mm drive on a M12x1.25 thread, torqued to 85 ft-lbs at the steering knuckle. At the caliper bracket, the brake caliper pin torques to 22 ft-lbs (12mm drive, M8x1.25 thread). For the rotor face, plan for a 5mm tool on a M5x0.8 stud; final torque is 4 ft-lbs (brake rotor set screw). Brake line banjo bolt tightens to 25 ft-lbs, takes a 10mm driver, runs on M10x1.0 threads, located at the caliper.

Engine — 2020 Toyota Land Cruiser

Engine bolt-by-bolt torque for the 2020 Toyota Land Cruiser, including the long block, valve covers, and intake. At the front of engine, the timing cover bolt torques to 10 ft-lbs (10mm drive, M6x1.0 thread). For the engine, plan for a 13mm tool on a M9x1.0 stud; final torque is Stage 1: 18 ft-lbs, Stage 2: +45° (connecting rod bolt). Cylinder head bolt tightens to Stage 1: 40 ft-lbs, Stage 2: +90°, takes a 14mm driver, runs on M10x1.5 threads, located at the engine. The water pump bolt uses a 12mm drive on a M8x1.25 thread, torqued to 15 ft-lbs at the front of engine. At the front of engine, the alternator bolt torques to 33 ft-lbs (14mm drive, M10x1.25 thread). For the oil pan, plan for a 14mm tool on a M12x1.25 stud; final torque is 30 ft-lbs (40 Nm) (oil drain plug). Spark plug tightens to 13 ft-lbs, takes a 16mm driver, runs on M14x1.25 threads, located at the cylinder head. The oil filter housing bolt uses a 10mm drive on a M6x1.0 thread, torqued to 10 ft-lbs at the engine block. At the cylinder head, the valve cover bolt torques to 8 ft-lbs (10mm drive, M6x1.0 thread).

Suspension — 2020 Toyota Land Cruiser

Suspension and chassis fastener torque for the 2020 Toyota Land Cruiser — strut, control arm, and sway bar values. For the wheel hub, plan for a 21mm tool on a M14x1.5 stud; final torque is 97 ft-lbs (131 Nm) (wheel lug nut). Lower control arm bolt tightens to 85 ft-lbs, takes a 19mm driver, runs on M14x2.0 threads, located at the subframe. The ball joint nut uses a 19mm drive on a M14x2.0 thread, torqued to 67 ft-lbs at the control arm. At the strut tower, the strut mount nut torques to 47 ft-lbs (14mm drive, M10x1.25 thread). For the sway bar, plan for a 17mm tool on a M12x1.25 stud; final torque is 43 ft-lbs (sway bar link nut).

Interior — 2020 Toyota Land Cruiser

Interior fasteners on the 2020 Toyota Land Cruiser. Front seat mount bolt tightens to 37 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the floor pan. The seat belt anchor bolt uses a 17mm drive on a M12x1.25 thread, torqued to 43 ft-lbs at the b-pillar. At the door panel, the door panel clip torques to Hand Tight (8mm drive, Push-Type thread). For the floor pan, plan for a 10mm tool on a M6x1.0 stud; final torque is 7 ft-lbs (center console bolt). Door hinge bolt tightens to 27 ft-lbs, takes a 12mm driver, runs on M8x1.25 threads, located at the door frame.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2020 Toyota Land Cruiser numbers above.

Loading the interactive 2020 Toyota Land Cruiser fastener lookup with per-bolt filtering, part links, and torque tools…