2008–2009 Toyota Sequoia Lug Nut Torque & Bolt Specs

The 2009 Toyota Sequoia lug nut torque is 97 ft-lbs (131 Nm), tightened with a 21mm socket on M14x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 97 ft-lbs (131 Nm) · Socket size: 21mm · Thread: M14x1.5.

This page is the OEM-referenced fastener summary for the 2009 Toyota Sequoia. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

These specifications also apply to the 2008 model years — identical specs on file for each year.

Toyota's engineering standard for wheel torque is unusually consistent across the lineup — nearly every passenger Toyota from the mid-2000s onward specs 76 ft-lbs (103 Nm) for the lug nuts with an M12x1.5 thread and 21mm socket. The big exceptions are the Tundra and Sequoia full-size trucks (97-110 ft-lbs), and the lug studs on older Camrys and Corollas (pre-2002) used a smaller M12x1.25 thread that does not interchange. Always confirm by checking the alloy stamp on the wheel hub if you are unsure.

Common fastener categories on the 2009 Toyota Sequoia

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2009 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2009 Toyota Sequoia?

The OEM-specified lug-nut torque for the 2009 Toyota Sequoia is 97 ft-lbs (131 Nm), using a 21mm socket on M14x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2009 Toyota Sequoia lug nuts?

The 2009 Toyota Sequoia uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2009 Toyota Sequoia fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Toyota Sequoia years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

All 15 2009 Toyota Sequoia fastener specs

Per-bolt torque, wrench size, and thread spec for the 2009 Toyota Sequoia, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 1 of the 15 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Brakes — 2009 Toyota Sequoia

Brake fasteners on the 2009 Toyota Sequoia — caliper bracket, slide pins, and banjo bolt torque follow. Wheel lug nut tightens to 97 ft-lbs (131 Nm), takes a 21mm driver, runs on M12x1.5 threads, located at the wheel hub. This figure is independently verified against OEM service data. The brake caliper bracket bolt uses a 17mm drive on a M12x1.25 thread, torqued to 85 ft-lbs at the steering knuckle. At the caliper bracket, the brake caliper bolt torques to 55 ft-lbs (14mm drive, M12x1.25 thread).

Engine — 2009 Toyota Sequoia

Engine bolt-by-bolt torque for the 2009 Toyota Sequoia, including the long block, valve covers, and intake. The oil drain plug uses a 14mm drive on a M14x1.5 thread, torqued to 30 ft-lbs at the oil pan. At the cylinder head, the valve cover bolt torques to 8 ft-lbs (10mm drive, M6x1.0 thread). For the engine, plan for a 14mm tool (cylinder head bolt). Connecting rod bolt takes a 13mm driver, located at the engine. The oil filter housing cap uses a 64mm drive on a M64x1.5 thread, torqued to 25 ft-lbs at the engine block.

Drivetrain — 2009 Toyota Sequoia

Drivetrain and driveline fasteners for the 2009 Toyota Sequoia — axle, transmission, and differential plugs. At the frame, the rear differential mount bolt torques to 85 ft-lbs (19mm drive, M14x1.5 thread). For the frame, plan for a 17mm tool on a M12x1.25 stud; final torque is 69 ft-lbs (transfer case mount bolt).

Suspension — 2009 Toyota Sequoia

Suspension and chassis fastener torque for the 2009 Toyota Sequoia — strut, control arm, and sway bar values. For the strut tower, plan for a 14mm tool on a M10x1.25 stud; final torque is 29 ft-lbs (trd strut brace bolt).

Body — 2009 Toyota Sequoia

Body fasteners on the 2009 Toyota Sequoia. Trd skid plate bolt tightens to 29 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the frame. The front skid plate bolt uses a 12mm drive on a M8x1.25 thread, torqued to 21 ft-lbs at the frame.

Transmission — 2009 Toyota Sequoia

Transmission fasteners on the 2009 Toyota Sequoia. The transmission drain plug uses a 24mm drive on a M20x1.5 thread, torqued to 29 ft-lbs at the transmission pan. At the transmission pan, the transmission pan bolt torques to 7 ft-lbs (10mm drive, M6x1.0 thread).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2009 Toyota Sequoia numbers above.

Loading the interactive 2009 Toyota Sequoia fastener lookup with per-bolt filtering, part links, and torque tools…