2022 Toyota Venza Lug Nut Torque & Bolt Specs

The 2022 Toyota Venza lug nut torque is 80 ft-lbs (108 Nm), tightened with a 21mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 21mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2022 Toyota Venza. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Toyota's engineering standard for wheel torque is unusually consistent across the lineup — nearly every passenger Toyota from the mid-2000s onward specs 76 ft-lbs (103 Nm) for the lug nuts with an M12x1.5 thread and 21mm socket. The big exceptions are the Tundra and Sequoia full-size trucks (97-110 ft-lbs), and the lug studs on older Camrys and Corollas (pre-2002) used a smaller M12x1.25 thread that does not interchange. Always confirm by checking the alloy stamp on the wheel hub if you are unsure.

Common fastener categories on the 2022 Toyota Venza

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2022 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2022 Toyota Venza?

The OEM-specified lug-nut torque for the 2022 Toyota Venza is 80 ft-lbs (108 Nm), using a 21mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2022 Toyota Venza lug nuts?

The 2022 Toyota Venza uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2022 Toyota Venza fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Toyota Venza years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2022 Toyota Venza oil drain plug torque & size

→ 2022 Toyota Venza suspension & steering torque specs (control arm, ball joint, tie rod)

All 23 2022 Toyota Venza fastener specs

Per-bolt torque, wrench size, and thread spec for the 2022 Toyota Venza, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Brakes — 2022 Toyota Venza

Brake fasteners on the 2022 Toyota Venza — caliper bracket, slide pins, and banjo bolt torque follow. Brake rotor set screw tightens to 4 ft-lbs, takes a 5mm driver, runs on M5x0.8 threads, located at the rotor face. The brake caliper pin uses a 12mm drive on a M8x1.25 thread, torqued to 22 ft-lbs at the caliper bracket. At the caliper, the brake line banjo bolt torques to 25 ft-lbs (10mm drive, M10x1.0 thread). For the steering knuckle, plan for a 17mm tool on a M12x1.25 stud; final torque is 85 ft-lbs (caliper bracket bolt).

Engine — 2022 Toyota Venza

Engine bolt-by-bolt torque for the 2022 Toyota Venza, including the long block, valve covers, and intake. The oil filter housing bolt uses a 10mm drive on a M6x1.0 thread, torqued to 10 ft-lbs at the engine block. At the engine, the cylinder head bolt torques to Stage 1: 40 ft-lbs, Stage 2: +90° (14mm drive, M10x1.5 thread). For the front of engine, plan for a 14mm tool on a M10x1.25 stud; final torque is 33 ft-lbs (alternator bolt). Timing cover bolt tightens to 10 ft-lbs, takes a 10mm driver, runs on M6x1.0 threads, located at the front of engine. The valve cover bolt uses a 10mm drive on a M6x1.0 thread, torqued to 8 ft-lbs at the cylinder head. At the oil pan, the oil drain plug torques to 30 ft-lbs (40 Nm) (14mm drive, M12x1.25 thread). For the engine, plan for a 13mm tool on a M9x1.0 stud; final torque is Stage 1: 18 ft-lbs, Stage 2: +45° (connecting rod bolt). Spark plug tightens to 13 ft-lbs, takes a 16mm driver, runs on M14x1.25 threads, located at the cylinder head. The water pump bolt uses a 12mm drive on a M8x1.25 thread, torqued to 15 ft-lbs at the front of engine.

Suspension — 2022 Toyota Venza

Suspension and chassis fastener torque for the 2022 Toyota Venza — strut, control arm, and sway bar values. At the strut tower, the strut mount nut torques to 47 ft-lbs (14mm drive, M10x1.25 thread). For the wheel hub, plan for a 21mm tool on a M12x1.5 stud; final torque is 80 ft-lbs (108 Nm) (wheel lug nut). Lower control arm bolt tightens to 85 ft-lbs, takes a 19mm driver, runs on M14x2.0 threads, located at the subframe. The sway bar link nut uses a 17mm drive on a M12x1.25 thread, torqued to 43 ft-lbs at the sway bar. At the control arm, the ball joint nut torques to 67 ft-lbs (19mm drive, M14x2.0 thread).

Interior — 2022 Toyota Venza

Interior fasteners on the 2022 Toyota Venza. For the door frame, plan for a 12mm tool on a M8x1.25 stud; final torque is 27 ft-lbs (door hinge bolt). Seat belt anchor bolt tightens to 43 ft-lbs, takes a 17mm driver, runs on M12x1.25 threads, located at the b-pillar. The front seat mount bolt uses a 14mm drive on a M10x1.25 thread, torqued to 37 ft-lbs at the floor pan. At the floor pan, the center console bolt torques to 7 ft-lbs (10mm drive, M6x1.0 thread). For the door panel, plan for a 8mm tool on a Push-Type stud; final torque is Hand Tight (door panel clip).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2022 Toyota Venza numbers above.

Loading the interactive 2022 Toyota Venza fastener lookup with per-bolt filtering, part links, and torque tools…