2002 Chevrolet Camaro Lug Nut Torque & Bolt Specs

The 2002 Chevrolet Camaro lug nut torque is 80 ft-lbs, tightened with a 3/4" socket on 7/16"-20 UNF studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs · Socket size: 3/4" · Thread: 7/16"-20 UNF.

This page is the OEM-referenced fastener summary for the 2002 Chevrolet Camaro. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

GM lug-nut torque clusters around 140 ft-lbs (190 Nm) for half-ton Silverado/Sierra and 100 ft-lbs for passenger cars like Malibu, Impala, and Cruze. GM heavy-duty trucks (2500HD/3500HD) jump to 165 ft-lbs. Most GM passenger cars use a 19mm socket; trucks moved from 22mm to 22mm-with-deep-well in 2014. Watch for GM's flat-flange lug nut design on the Silverado — the standard cone-seat aftermarket lugs will not seat correctly.

Common fastener categories on the 2002 Chevrolet Camaro

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2002 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2002 Chevrolet Camaro?

The OEM-specified lug-nut torque for the 2002 Chevrolet Camaro is 80 ft-lbs, using a 3/4" socket on 7/16"-20 UNF thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2002 Chevrolet Camaro lug nuts?

The 2002 Chevrolet Camaro uses a 3/4" socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2002 Chevrolet Camaro fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Chevrolet Camaro years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2002 Chevrolet Camaro suspension & steering torque specs (control arm, ball joint, tie rod)

All 8 2002 Chevrolet Camaro fastener specs

Per-bolt torque, wrench size, and thread spec for the 2002 Chevrolet Camaro, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 2002 Chevrolet Camaro

Wheel and lug nut spec for the 2002 Chevrolet Camaro. For the all four wheels, plan for a 3/4" tool on a 7/16"-20 UNF stud; final torque is 80 ft-lbs (lug nut).

Brakes — 2002 Chevrolet Camaro

Brake fasteners on the 2002 Chevrolet Camaro — caliper bracket, slide pins, and banjo bolt torque follow. Front brake caliper slide pin tightens to See notes, takes a See notes driver, runs on See notes threads, located at the front caliper slide pin. The front brake caliper bracket bolt uses a See notes drive on a See notes thread, torqued to See notes at the front brake caliper bracket to knuckle.

Engine — 2002 Chevrolet Camaro

Engine bolt-by-bolt torque for the 2002 Chevrolet Camaro, including the long block, valve covers, and intake. The oil drain plug uses a See notes drive on a See notes thread, torqued to See notes at the oil pan. At the cylinder head, the spark plug torques to 15 ft-lbs (5/8" (16mm) drive, M14x1.25 thread).

Suspension — 2002 Chevrolet Camaro

Suspension and chassis fastener torque for the 2002 Chevrolet Camaro — strut, control arm, and sway bar values. At the front axle hub bearing, the front hub/bearing nut torques to See notes (See notes drive, See notes thread). For the front sway bar end link, plan for a 3/4" tool on a 1/2"-20 UNF stud; final torque is 13 ft-lbs (sway bar end link nut).

Steering — 2002 Chevrolet Camaro

Steering linkage fasteners on the 2002 Chevrolet Camaro. For the outer tie rod end to steering knuckle, plan for a 3/4" tool on a 1/2"-20 UNF stud; final torque is 35 ft-lbs (tie rod end nut).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2002 Chevrolet Camaro numbers above.

Loading the interactive 2002 Chevrolet Camaro fastener lookup with per-bolt filtering, part links, and torque tools…