2023 Nissan Altima Lug Nut Torque & Bolt Specs

The 2023 Nissan Altima lug nut torque is 80 ft-lbs (108 Nm), tightened with a 21mm socket on M12x1.25 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 21mm · Thread: M12x1.25.

This page is the OEM-referenced fastener summary for the 2023 Nissan Altima. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Nissan lug-nut torque is 83 ft-lbs (113 Nm) for nearly every passenger model since 2000 with an M12x1.25 thread (note: tighter pitch than Toyota/Honda's M12x1.5 — the lugs do not cross-thread cleanly with neighboring makes). Socket size is 21mm. Titans and Armadas use a larger M14x1.5 thread at 133 ft-lbs.

Common fastener categories on the 2023 Nissan Altima

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2023 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2023 Nissan Altima?

The OEM-specified lug-nut torque for the 2023 Nissan Altima is 80 ft-lbs (108 Nm), using a 21mm socket on M12x1.25 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2023 Nissan Altima lug nuts?

The 2023 Nissan Altima uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2023 Nissan Altima fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Nissan Altima years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2023 Nissan Altima oil drain plug torque & size

→ 2023 Nissan Altima suspension & steering torque specs (control arm, ball joint, tie rod)

All 15 2023 Nissan Altima fastener specs

Per-bolt torque, wrench size, and thread spec for the 2023 Nissan Altima, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 1 of the 15 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data.

Wheels — 2023 Nissan Altima

Wheel and lug nut spec for the 2023 Nissan Altima. For the wheel hub, plan for a Hex tool on a M12x1.25 stud; final torque is 80 ft-lbs (108 Nm) (wheel lug nut).

Brakes — 2023 Nissan Altima

Brake fasteners on the 2023 Nissan Altima — caliper bracket, slide pins, and banjo bolt torque follow. Brake caliper mounting bolt tightens to See manual, takes a Hex driver, runs on M14x1.5 threads, located at the front/rear brake caliper. The brake caliper pin bolt uses a Hex drive on a M10x1.25 thread, torqued to 16-23 ft-lbs at the brake caliper slide pin.

Engine — 2023 Nissan Altima

Engine bolt-by-bolt torque for the 2023 Nissan Altima, including the long block, valve covers, and intake. The intake manifold bolt uses a Hex drive on a M10x1.25 thread, torqued to 18-22 ft-lbs (20 Nm) at the intake manifold. At the valve cover, the valve cover bolt torques to 7-9 ft-lbs (10 Nm) (Hex drive, M8x1.25 thread). For the engine block, plan for a Canister tool on a M20x1.5 stud; final torque is Hand tight (18 Nm) (oil filter). This figure is independently verified against OEM service data. Oil drain plug tightens to 25 ft-lbs (34 Nm), takes a Hex driver, runs on M12x1.25 threads, located at the oil pan. The oil pan bolt (10mm) uses a Hex drive on a M10x1.25 thread, torqued to 16-22 ft-lbs at the oil pan - upper. At the oil pan - lower, the oil pan bolt (8mm) torques to 6-8 ft-lbs (9 Nm) (Hex drive, M8x1.25 thread).

Suspension — 2023 Nissan Altima

Suspension and chassis fastener torque for the 2023 Nissan Altima — strut, control arm, and sway bar values. At the strut to knuckle, the front strut lower bolt torques to 100-110 ft-lbs (Hex drive, M14x1.5 thread). For the rear shock mount, plan for a Hex tool on a M12x1.25 stud; final torque is 50-65 ft-lbs (rear shock upper bolt).

Wheels & Tires — 2023 Nissan Altima

Wheels & Tires fasteners on the 2023 Nissan Altima. For the wheel hub, plan for a 21mm tool on a M12x1.25 stud; final torque is 80 ft-lbs (108 Nm) (lug nut).

General — 2023 Nissan Altima

General fasteners on the 2023 Nissan Altima. Rear shock lower bolt tightens to 70-85 ft-lbs, takes a Hex driver, runs on M14x1.5 threads, located at the rear axle. The spark plug uses a Hex drive on a M12x1.25 thread, torqued to 14 ft-lbs (19 Nm) at the cylinder head.

Transmission — 2023 Nissan Altima

Transmission fasteners on the 2023 Nissan Altima. The transmission drain plug uses a Hex drive on a M14x1.5 thread, torqued to See manual at the transmission pan.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2023 Nissan Altima numbers above.

Loading the interactive 2023 Nissan Altima fastener lookup with per-bolt filtering, part links, and torque tools…