2022 Nissan Altima Lug Nut Torque & Bolt Specs

The 2022 Nissan Altima lug nut torque is 80 ft-lbs (108 Nm), tightened with a Hex socket on M12x1.25 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: Hex · Thread: M12x1.25.

This page is the OEM-referenced fastener summary for the 2022 Nissan Altima. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Nissan lug-nut torque is 83 ft-lbs (113 Nm) for nearly every passenger model since 2000 with an M12x1.25 thread (note: tighter pitch than Toyota/Honda's M12x1.5 — the lugs do not cross-thread cleanly with neighboring makes). Socket size is 21mm. Titans and Armadas use a larger M14x1.5 thread at 133 ft-lbs.

Common fastener categories on the 2022 Nissan Altima

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2022 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2022 Nissan Altima?

The OEM-specified lug-nut torque for the 2022 Nissan Altima is 80 ft-lbs (108 Nm), using a Hex socket on M12x1.25 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2022 Nissan Altima lug nuts?

The 2022 Nissan Altima uses a Hex socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2022 Nissan Altima fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Nissan Altima years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2022 Nissan Altima oil drain plug torque & size

→ 2022 Nissan Altima suspension & steering torque specs (control arm, ball joint, tie rod)

All 15 2022 Nissan Altima fastener specs

Per-bolt torque, wrench size, and thread spec for the 2022 Nissan Altima, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 1 of the 15 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data.

Wheels — 2022 Nissan Altima

Wheel and lug nut spec for the 2022 Nissan Altima. At the wheel hub, the wheel lug nut torques to 80 ft-lbs (108 Nm) (Hex drive, M12x1.25 thread).

Brakes — 2022 Nissan Altima

Brake fasteners on the 2022 Nissan Altima — caliper bracket, slide pins, and banjo bolt torque follow. For the front/rear brake caliper, plan for a Hex tool on a M14x1.5 stud; final torque is See manual (brake caliper mounting bolt). Brake caliper pin bolt tightens to 16-23 ft-lbs, takes a Hex driver, runs on M10x1.25 threads, located at the brake caliper slide pin.

Engine — 2022 Nissan Altima

Engine bolt-by-bolt torque for the 2022 Nissan Altima, including the long block, valve covers, and intake. Oil pan bolt (10mm) tightens to 16-22 ft-lbs, takes a Hex driver, runs on M10x1.25 threads, located at the oil pan - upper. The valve cover bolt uses a Hex drive on a M8x1.25 thread, torqued to 7-9 ft-lbs (10 Nm) at the valve cover. At the engine block, the oil filter torques to Hand tight (18 Nm) (Canister drive, M20x1.5 thread). Confirmed against manufacturer service literature. For the oil pan - lower, plan for a Hex tool on a M8x1.25 stud; final torque is 6-8 ft-lbs (9 Nm) (oil pan bolt (8mm)). Oil drain plug tightens to 25 ft-lbs (34 Nm), takes a Hex driver, runs on M12x1.25 threads, located at the oil pan. The intake manifold bolt uses a Hex drive on a M10x1.25 thread, torqued to 18-22 ft-lbs (20 Nm) at the intake manifold.

Suspension — 2022 Nissan Altima

Suspension and chassis fastener torque for the 2022 Nissan Altima — strut, control arm, and sway bar values. The front strut lower bolt uses a Hex drive on a M14x1.5 thread, torqued to 100-110 ft-lbs at the strut to knuckle. At the rear shock mount, the rear shock upper bolt torques to 50-65 ft-lbs (Hex drive, M12x1.25 thread).

Transmission — 2022 Nissan Altima

Transmission fasteners on the 2022 Nissan Altima. At the transmission pan, the transmission drain plug torques to See manual (Hex drive, M14x1.5 thread).

General — 2022 Nissan Altima

General fasteners on the 2022 Nissan Altima. For the rear axle, plan for a Hex tool on a M14x1.5 stud; final torque is 70-85 ft-lbs (rear shock lower bolt). Spark plug tightens to 14 ft-lbs (19 Nm), takes a Hex driver, runs on M12x1.25 threads, located at the cylinder head.

Wheels & Tires — 2022 Nissan Altima

Wheels & Tires fasteners on the 2022 Nissan Altima. Lug nut tightens to 80 ft-lbs (108 Nm), takes a 21mm driver, runs on M12x1.25 threads, located at the wheel hub.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2022 Nissan Altima numbers above.

Loading the interactive 2022 Nissan Altima fastener lookup with per-bolt filtering, part links, and torque tools…