2024 Toyota 4Runner Lug Nut Torque & Bolt Specs

The 2024 Toyota 4Runner lug nut torque is 112 Nm (83 ft-lbs), tightened with a 21mm socket on M12 x 1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 112 Nm (83 ft-lbs) · Socket size: 21mm · Thread: M12 x 1.5.

This page is the OEM-referenced fastener summary for the 2024 Toyota 4Runner. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Toyota's engineering standard for wheel torque is unusually consistent across the lineup — nearly every passenger Toyota from the mid-2000s onward specs 76 ft-lbs (103 Nm) for the lug nuts with an M12x1.5 thread and 21mm socket. The big exceptions are the Tundra and Sequoia full-size trucks (97-110 ft-lbs), and the lug studs on older Camrys and Corollas (pre-2002) used a smaller M12x1.25 thread that does not interchange. Always confirm by checking the alloy stamp on the wheel hub if you are unsure.

Common fastener categories on the 2024 Toyota 4Runner

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2024 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2024 Toyota 4Runner?

The OEM-specified lug-nut torque for the 2024 Toyota 4Runner is 112 Nm (83 ft-lbs), using a 21mm socket on M12 x 1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2024 Toyota 4Runner lug nuts?

The 2024 Toyota 4Runner uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2024 Toyota 4Runner fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Toyota 4Runner years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2024 Toyota 4Runner oil drain plug torque & size

All 12 2024 Toyota 4Runner fastener specs

Per-bolt torque, wrench size, and thread spec for the 2024 Toyota 4Runner, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 2024 Toyota 4Runner

Wheel and lug nut spec for the 2024 Toyota 4Runner. Wheel lug nut tightens to 112 Nm (83 ft-lbs), takes a 21mm driver, runs on M12 x 1.5 threads, located at the wheel hub.

Brakes — 2024 Toyota 4Runner

Brake fasteners on the 2024 Toyota 4Runner — caliper bracket, slide pins, and banjo bolt torque follow. The brake caliper pin uses a 12mm drive on a M8x1.25 thread, torqued to 22 ft-lbs at the caliper bracket. At the caliper, the brake line banjo bolt torques to 25 ft-lbs (10mm drive, M10x1.0 thread).

Engine — 2024 Toyota 4Runner

Engine bolt-by-bolt torque for the 2024 Toyota 4Runner, including the long block, valve covers, and intake. At the engine, the connecting rod bolt torques to Stage 1: 18 ft-lbs, Stage 2: +45° (13mm drive, M9x1.0 thread). For the cylinder head, plan for a 10mm tool on a M6x1.0 stud; final torque is 8 ft-lbs (valve cover bolt). Cylinder head bolt tightens to Stage 1: 40 ft-lbs, Stage 2: +90°, takes a 14mm driver, runs on M10x1.5 threads, located at the engine. The water pump bolt uses a 12mm drive on a M8x1.25 thread, torqued to 15 ft-lbs at the front of engine. At the oil pan, the oil drain plug torques to 30 ft-lbs (14mm drive, M14x1.5 thread).

Suspension — 2024 Toyota 4Runner

Suspension and chassis fastener torque for the 2024 Toyota 4Runner — strut, control arm, and sway bar values. For the sway bar, plan for a 17mm tool on a M12x1.25 stud; final torque is 43 ft-lbs (sway bar link nut).

Interior — 2024 Toyota 4Runner

Interior fasteners on the 2024 Toyota 4Runner. Door panel clip tightens to Hand Tight, takes a 8mm driver, runs on Push-Type threads, located at the door panel. The seat belt anchor bolt uses a 17mm drive on a M12x1.25 thread, torqued to 43 ft-lbs at the b-pillar. At the door frame, the door hinge bolt torques to 27 ft-lbs (12mm drive, M8x1.25 thread).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2024 Toyota 4Runner numbers above.

Loading the interactive 2024 Toyota 4Runner fastener lookup with per-bolt filtering, part links, and torque tools…