2012 Toyota 4Runner Lug Nut Torque & Bolt Specs

The 2012 Toyota 4Runner lug nut torque is 110 Nm (81 ft-lbs), tightened with a 21mm socket on M12 x 1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 110 Nm (81 ft-lbs) · Socket size: 21mm · Thread: M12 x 1.5.

This page is the OEM-referenced fastener summary for the 2012 Toyota 4Runner. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Toyota's engineering standard for wheel torque is unusually consistent across the lineup — nearly every passenger Toyota from the mid-2000s onward specs 76 ft-lbs (103 Nm) for the lug nuts with an M12x1.5 thread and 21mm socket. The big exceptions are the Tundra and Sequoia full-size trucks (97-110 ft-lbs), and the lug studs on older Camrys and Corollas (pre-2002) used a smaller M12x1.25 thread that does not interchange. Always confirm by checking the alloy stamp on the wheel hub if you are unsure.

Common fastener categories on the 2012 Toyota 4Runner

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2012 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2012 Toyota 4Runner?

The OEM-specified lug-nut torque for the 2012 Toyota 4Runner is 110 Nm (81 ft-lbs), using a 21mm socket on M12 x 1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2012 Toyota 4Runner lug nuts?

The 2012 Toyota 4Runner uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2012 Toyota 4Runner fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Toyota 4Runner years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2012 Toyota 4Runner oil drain plug torque & size

All 10 2012 Toyota 4Runner fastener specs

Per-bolt torque, wrench size, and thread spec for the 2012 Toyota 4Runner, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 2 of the 10 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Wheels — 2012 Toyota 4Runner

Wheel and lug nut spec for the 2012 Toyota 4Runner. For the wheel hub, plan for a 21mm tool on a M12 x 1.5 stud; final torque is 110 Nm (81 ft-lbs) (wheel lug nut).

Brakes — 2012 Toyota 4Runner

Brake fasteners on the 2012 Toyota 4Runner — caliper bracket, slide pins, and banjo bolt torque follow. Caliper bracket bolt tightens to 91-137 ft-lbs (123-186 Nm), takes a 17mm driver, runs on M12x1.25 threads, located at the steering knuckle. This figure is independently verified against OEM service data.

Engine — 2012 Toyota 4Runner

Engine bolt-by-bolt torque for the 2012 Toyota 4Runner, including the long block, valve covers, and intake. The alternator bolt uses a 14mm drive on a M10x1.25 thread, torqued to 33 ft-lbs at the front of engine. At the oil pan, the oil drain plug torques to 26 ft-lbs (35 Nm). Confirmed against manufacturer service literature. For the engine, plan for a 14mm tool on a M10x1.5 stud; final torque is Stage 1: 40 ft-lbs, Stage 2: +90° (cylinder head bolt). Water pump bolt tightens to 15 ft-lbs, takes a 12mm driver, runs on M8x1.25 threads, located at the front of engine. The connecting rod bolt uses a 13mm drive on a M9x1.0 thread, torqued to Stage 1: 18 ft-lbs, Stage 2: +45° at the engine. At the engine block, the oil filter housing bolt torques to 10 ft-lbs (10mm drive, M6x1.0 thread).

Suspension — 2012 Toyota 4Runner

Suspension and chassis fastener torque for the 2012 Toyota 4Runner — strut, control arm, and sway bar values. At the sway bar, the sway bar link nut torques to 43 ft-lbs (17mm drive, M12x1.25 thread).

Interior — 2012 Toyota 4Runner

Interior fasteners on the 2012 Toyota 4Runner. For the floor pan, plan for a 10mm tool on a M6x1.0 stud; final torque is 7 ft-lbs (center console bolt).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2012 Toyota 4Runner numbers above.

Loading the interactive 2012 Toyota 4Runner fastener lookup with per-bolt filtering, part links, and torque tools…