2004 Toyota 4Runner Lug Nut Torque & Bolt Specs

The 2004 Toyota 4Runner lug nut torque is 80 ft-lbs (108 Nm), tightened with a 21mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 21mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2004 Toyota 4Runner. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Toyota's engineering standard for wheel torque is unusually consistent across the lineup — nearly every passenger Toyota from the mid-2000s onward specs 76 ft-lbs (103 Nm) for the lug nuts with an M12x1.5 thread and 21mm socket. The big exceptions are the Tundra and Sequoia full-size trucks (97-110 ft-lbs), and the lug studs on older Camrys and Corollas (pre-2002) used a smaller M12x1.25 thread that does not interchange. Always confirm by checking the alloy stamp on the wheel hub if you are unsure.

Common fastener categories on the 2004 Toyota 4Runner

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2004 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2004 Toyota 4Runner?

The OEM-specified lug-nut torque for the 2004 Toyota 4Runner is 80 ft-lbs (108 Nm), using a 21mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2004 Toyota 4Runner lug nuts?

The 2004 Toyota 4Runner uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2004 Toyota 4Runner fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Toyota 4Runner years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2004 Toyota 4Runner oil drain plug torque & size

All 12 2004 Toyota 4Runner fastener specs

Per-bolt torque, wrench size, and thread spec for the 2004 Toyota 4Runner, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 1 of the 12 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Wheels — 2004 Toyota 4Runner

Wheel and lug nut spec for the 2004 Toyota 4Runner. At the wheel hub, the wheel lug nut torques to 80 ft-lbs (108 Nm) (21mm drive, M12x1.5 thread).

Brakes — 2004 Toyota 4Runner

Brake fasteners on the 2004 Toyota 4Runner — caliper bracket, slide pins, and banjo bolt torque follow. For the front knuckle, plan for a 17mm hex tool on a M12 stud; final torque is 91 ft-lb (front caliper bracket bolt). Rear caliper bracket bolt tightens to 77 ft-lb, takes a 17mm hex driver, runs on M12 threads, located at the rear axle. The rear caliper slide pin uses a 12mm hex drive on a M10 thread, torqued to 65 ft-lb at the rear caliper.

Engine — 2004 Toyota 4Runner

Engine bolt-by-bolt torque for the 2004 Toyota 4Runner, including the long block, valve covers, and intake. Oil drain plug tightens to 30 ft-lbs (40 Nm), runs on M12x1.25 threads, located at the oil pan. This figure is independently verified against OEM service data. The spark plug uses a 5/8" (16mm) drive on a M14x1.25 thread, torqued to 15 ft-lbs (20 Nm) at the cylinder head. At the engine, the cylinder head bolt torques to Stage 1: 40 ft-lbs, Stage 2: +90° (14mm drive, M10x1.5 thread). For the engine, plan for a 13mm tool on a M9x1.0 stud; final torque is Stage 1: 18 ft-lbs, Stage 2: +45° (connecting rod bolt).

Drivetrain — 2004 Toyota 4Runner

Drivetrain and driveline fasteners for the 2004 Toyota 4Runner — axle, transmission, and differential plugs. The front axle hub nut uses a 35mm hex drive on a M30x1.5 thread, torqued to 173 ft-lb at the front hub (4wd).

Suspension — 2004 Toyota 4Runner

Suspension and chassis fastener torque for the 2004 Toyota 4Runner — strut, control arm, and sway bar values. At the front lca to knuckle, the front lower control arm ball joint torques to 118 ft-lb (19mm hex drive, M14 thread). For the front uca, plan for a 22mm hex tool on a M16 stud; final torque is 85 ft-lb (upper control arm through bolt).

Wheel Hardware — 2004 Toyota 4Runner

Wheel Hardware fasteners on the 2004 Toyota 4Runner. For the all wheels, plan for a 21mm hex tool on a M12x1.5 stud; final torque is 80 ft-lbs (108 Nm) (lug nut).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2004 Toyota 4Runner numbers above.

Loading the interactive 2004 Toyota 4Runner fastener lookup with per-bolt filtering, part links, and torque tools…