2018 Toyota Highlander Lug Nut Torque & Bolt Specs

The 2018 Toyota Highlander lug nut torque is 80 ft-lbs (108 Nm), tightened with a 21mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 21mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2018 Toyota Highlander. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Toyota's engineering standard for wheel torque is unusually consistent across the lineup — nearly every passenger Toyota from the mid-2000s onward specs 76 ft-lbs (103 Nm) for the lug nuts with an M12x1.5 thread and 21mm socket. The big exceptions are the Tundra and Sequoia full-size trucks (97-110 ft-lbs), and the lug studs on older Camrys and Corollas (pre-2002) used a smaller M12x1.25 thread that does not interchange. Always confirm by checking the alloy stamp on the wheel hub if you are unsure.

Common fastener categories on the 2018 Toyota Highlander

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2018 model-year work: This era introduced widespread torque-to-yield (TTY) bolts on head, main, and crank pulley fasteners. TTY bolts stretch permanently when torqued and must not be reused — the spec calls for a fresh bolt every time. Always verify TTY status against the FSM before reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2018 Toyota Highlander?

The OEM-specified lug-nut torque for the 2018 Toyota Highlander is 80 ft-lbs (108 Nm), using a 21mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2018 Toyota Highlander lug nuts?

The 2018 Toyota Highlander uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2018 Toyota Highlander fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Toyota Highlander years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2018 Toyota Highlander oil drain plug torque & size

→ 2018 Toyota Highlander suspension & steering torque specs (control arm, ball joint, tie rod)

All 14 2018 Toyota Highlander fastener specs

Per-bolt torque, wrench size, and thread spec for the 2018 Toyota Highlander, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 1 of the 14 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Brakes — 2018 Toyota Highlander

Brake fasteners on the 2018 Toyota Highlander — caliper bracket, slide pins, and banjo bolt torque follow. The brake caliper pin uses a 12mm drive on a M8x1.25 thread, torqued to 22 ft-lbs at the caliper bracket. At the caliper, the brake line banjo bolt torques to 25 ft-lbs (10mm drive, M10x1.0 thread).

Engine — 2018 Toyota Highlander

Engine bolt-by-bolt torque for the 2018 Toyota Highlander, including the long block, valve covers, and intake. At the front of engine, the water pump bolt torques to 15 ft-lbs (12mm drive, M8x1.25 thread). For the oil pan, plan for the right driver on a M12x1.25 stud; final torque is 30 ft-lbs (40 Nm) (oil drain plug). Confirmed against manufacturer service literature. Connecting rod bolt takes a 13mm driver, located at the engine. The timing cover bolt uses a 10mm drive on a M6x1.0 thread, torqued to 10 ft-lbs at the front of engine. The spark plug torques to 18 ft-lbs (25 Nm) (5/8in drive, M14x1.25 thread). For the engine block, plan for a 10mm tool on a M6x1.0 stud; final torque is 10 ft-lbs (oil filter housing bolt). Cylinder head bolt takes a 14mm driver, located at the engine.

Suspension — 2018 Toyota Highlander

Suspension and chassis fastener torque for the 2018 Toyota Highlander — strut, control arm, and sway bar values. For the sway bar, plan for a 17mm tool on a M12x1.25 stud; final torque is 43 ft-lbs (sway bar link nut). Lower control arm bolt tightens to 85 ft-lbs, takes a 19mm driver, runs on M14x2.0 threads, located at the subframe. The wheel lug nut uses a 21mm drive on a M12x1.5 thread, torqued to 80 ft-lbs (108 Nm) at the wheel hub.

Interior — 2018 Toyota Highlander

Interior fasteners on the 2018 Toyota Highlander. Door panel clip tightens to Hand Tight, takes a 8mm driver, runs on Push-Type threads, located at the door panel. The seat belt anchor bolt uses a 17mm drive on a M12x1.25 thread, torqued to 43 ft-lbs at the b-pillar.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2018 Toyota Highlander numbers above.

Loading the interactive 2018 Toyota Highlander fastener lookup with per-bolt filtering, part links, and torque tools…