2019 Toyota Highlander Lug Nut Torque & Bolt Specs

The 2019 Toyota Highlander lug nut torque is 76 ft-lbs (103 Nm), tightened with a 21mm socket on M12 x 1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 76 ft-lbs (103 Nm) · Socket size: 21mm · Thread: M12 x 1.5.

This page is the OEM-referenced fastener summary for the 2019 Toyota Highlander. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Toyota's engineering standard for wheel torque is unusually consistent across the lineup — nearly every passenger Toyota from the mid-2000s onward specs 76 ft-lbs (103 Nm) for the lug nuts with an M12x1.5 thread and 21mm socket. The big exceptions are the Tundra and Sequoia full-size trucks (97-110 ft-lbs), and the lug studs on older Camrys and Corollas (pre-2002) used a smaller M12x1.25 thread that does not interchange. Always confirm by checking the alloy stamp on the wheel hub if you are unsure.

Common fastener categories on the 2019 Toyota Highlander

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2019 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2019 Toyota Highlander?

The OEM-specified lug-nut torque for the 2019 Toyota Highlander is 76 ft-lbs (103 Nm), using a 21mm socket on M12 x 1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2019 Toyota Highlander lug nuts?

The 2019 Toyota Highlander uses a 21mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2019 Toyota Highlander fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Toyota Highlander years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2019 Toyota Highlander oil drain plug torque & size

All 15 2019 Toyota Highlander fastener specs

Per-bolt torque, wrench size, and thread spec for the 2019 Toyota Highlander, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 4 of the 15 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Wheels — 2019 Toyota Highlander

Wheel and lug nut spec for the 2019 Toyota Highlander. Wheel lug nut tightens to 76 ft-lbs (103 Nm), takes a 21mm driver, runs on M12 x 1.5 threads, located at the wheel hub. This figure is independently verified against OEM service data.

Brakes — 2019 Toyota Highlander

Brake fasteners on the 2019 Toyota Highlander — caliper bracket, slide pins, and banjo bolt torque follow. The brake line banjo bolt uses a 10mm drive on a M10x1.0 thread, torqued to 25 ft-lbs at the caliper. At the caliper bracket, the brake caliper pin torques to 22 ft-lbs (12mm drive, M8x1.25 thread). For the steering knuckle, plan for a 17mm tool on a M12x1.25 stud; final torque is 77 ft-lbs (104 Nm) (caliper bracket bolt). This figure is independently verified against OEM service data.

Engine — 2019 Toyota Highlander

Engine bolt-by-bolt torque for the 2019 Toyota Highlander, including the long block, valve covers, and intake. At the cylinder head, the spark plug torques to 13 ft-lbs (18 Nm) (16mm drive, M14x1.25 thread). Confirmed against manufacturer service literature. For the engine block, plan for a 10mm tool on a M6x1.0 stud; final torque is 10 ft-lbs (oil filter housing bolt). Oil drain plug tightens to 27 ft-lbs (37 Nm), located at the oil pan. OEM-verified spec. The cylinder head bolt uses a 14mm drive on a M10x1.5 thread, torqued to Stage 1: 40 ft-lbs, Stage 2: +90° at the engine. At the engine, the connecting rod bolt torques to Stage 1: 18 ft-lbs, Stage 2: +45° (13mm drive, M9x1.0 thread). For the front of engine, plan for a 12mm tool on a M8x1.25 stud; final torque is 15 ft-lbs (water pump bolt). Timing cover bolt tightens to 10 ft-lbs, takes a 10mm driver, runs on M6x1.0 threads, located at the front of engine. The valve cover bolt uses a 10mm drive on a M6x1.0 thread, torqued to 8 ft-lbs at the cylinder head.

Suspension — 2019 Toyota Highlander

Suspension and chassis fastener torque for the 2019 Toyota Highlander — strut, control arm, and sway bar values. For the strut tower, plan for a 14mm tool on a M10x1.25 stud; final torque is 47 ft-lbs (strut mount nut). Sway bar link nut tightens to 43 ft-lbs, takes a 17mm driver, runs on M12x1.25 threads, located at the sway bar.

Interior — 2019 Toyota Highlander

Interior fasteners on the 2019 Toyota Highlander. Seat belt anchor bolt tightens to 43 ft-lbs, takes a 17mm driver, runs on M12x1.25 threads, located at the b-pillar.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2019 Toyota Highlander numbers above.

Loading the interactive 2019 Toyota Highlander fastener lookup with per-bolt filtering, part links, and torque tools…