2007 Hyundai Elantra Suspension & Steering Torque Specs

OEM-referenced torque, socket, and thread specs for the 9 front and rear suspension and steering fasteners on the 2007 Hyundai Elantra — including the Front Lower Control Arm Bolts (torques to 98.1-117.7 Nm (72.3-86.8 ft-lb), 17-19mm socket, M14 x 1.5 thread). Every value is safety-critical; verify against your service manual and use a calibrated torque wrench. Full bolt specs for the rest of the vehicle are linked below.

Control Arms & Ball Joints torque — 2007 Hyundai Elantra

On the 2007 Hyundai Elantra, the control arms & ball joints fasteners are: Front Lower Control Arm Bolts (torques to 98.1-117.7 Nm (72.3-86.8 ft-lb), 17-19mm socket, M14 x 1.5 thread). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Struts, Shocks & Springs torque — 2007 Hyundai Elantra

On the 2007 Hyundai Elantra, the struts, shocks & springs fasteners are: Front Strut to Knuckle Bolts (torques to 110-130 Nm (81-96 ft-lb), 17mm bolt / 19mm nut socket, M14 x 1.5 thread); Front Strut Top Nut (torques to 40-50 Nm (29-36 ft-lb), 17mm with hex hold socket, M14 x 1.5 thread); Rear Shock Lower Bolt (torques to 80-110 Nm (59-81 ft-lb), 17mm socket, M12 x 1.25 thread). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Sway Bar & Stabilizer Links torque — 2007 Hyundai Elantra

On the 2007 Hyundai Elantra, the sway bar & stabilizer links fasteners are: Sway Bar End Link Nut (torques to 98.1-117.7 Nm (72.3-86.8 ft-lb), 17mm socket, M12 x 1.25 thread). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Steering (Tie Rods & Linkage) torque — 2007 Hyundai Elantra

On the 2007 Hyundai Elantra, the steering (tie rods & linkage) fasteners are: Tie Rod End Nut (torques to 24-34 Nm (18-25 ft-lb), 17mm socket, M12 x 1.25 thread). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

Other Suspension Fasteners torque — 2007 Hyundai Elantra

On the 2007 Hyundai Elantra, the other suspension fasteners fasteners are: Front Hub / Axle Nut (torques to 255 Nm (188 ft-lb), 32mm socket, M24 x 1.5 thread); Front Hub/Bearing Nut (torques to 148-192 ft-lbs, 32mm socket, M24x1.5 thread); Rear Hub / Axle Nut (torques to 200-260 Nm (148-192 ft-lb), 32mm socket, M24 x 1.5 thread). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.

How to torque Elantra suspension & steering fasteners

Torque suspension and steering fasteners with the vehicle at ride height (wheels loaded) wherever a bushing is involved — tightening a control-arm or sway-bar bushing bolt with the suspension hanging pre-loads the rubber and it fails early. Clean the threads, start every fastener by hand to avoid cross-threading, and make the final pass with a calibrated torque wrench rather than an impact gun. Ball-joint and tie-rod castle nuts take a new cotter pin; never back a castle nut off to line up the hole — only tighten to the next slot.

Related lookups

Loading interactive lookup…