2009 Chrysler Sebring Suspension & Steering Torque Specs
OEM-referenced torque, socket, and thread specs for the 10 front and rear suspension and steering fasteners on the 2009 Chrysler Sebring — including the Front Lower Control Arm Front Pivot Bolt (torques to 129 ft-lbs (175 Nm)). Every value is safety-critical; verify against your service manual and use a calibrated torque wrench. Full bolt specs for the rest of the vehicle are linked below.
Control Arms & Ball Joints torque — 2009 Chrysler Sebring
On the 2009 Chrysler Sebring, the control arms & ball joints fasteners are: Front Lower Control Arm Front Pivot Bolt (torques to 129 ft-lbs (175 Nm)); Front Lower Control Arm Rear Pivot Bolt (torques to 107 ft-lbs (145 Nm)); Front Wheel Hub-to-Knuckle Bolts (torques to 35 ft-lbs (47 Nm)); Lower Ball Joint Pinch Bolt (torques to 70 ft-lbs (95 Nm)). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.
Struts, Shocks & Springs torque — 2009 Chrysler Sebring
On the 2009 Chrysler Sebring, the struts, shocks & springs fasteners are: Front Strut Upper Mount Nuts (torques to 40 ft-lbs (54 Nm)); Front Strut-to-Knuckle Bolts (torques to 103 ft-lbs (140 Nm)); Rear Shock Lower Bolt (torques to 73 ft-lbs (99 Nm)). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.
Sway Bar & Stabilizer Links torque — 2009 Chrysler Sebring
On the 2009 Chrysler Sebring, the sway bar & stabilizer links fasteners are: Front Sway Bar End-Link Nut (torques to 35 ft-lbs (47 Nm)). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.
Steering (Tie Rods & Linkage) torque — 2009 Chrysler Sebring
On the 2009 Chrysler Sebring, the steering (tie rods & linkage) fasteners are: Outer Tie Rod End Nut (torques to 40 ft-lbs (54 Nm)). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.
Wheel Hub & Bearing torque — 2009 Chrysler Sebring
On the 2009 Chrysler Sebring, the wheel hub & bearing fasteners are: Rear Wheel Hub/Bearing Bolts (torques to 77 ft-lbs (104 Nm)). Suspension and steering bolts are safety-critical — use a calibrated torque wrench, replace any prevailing-torque (locking) nut that has been removed, and confirm the value against your service manual before reassembly.
How to torque Sebring suspension & steering fasteners
Torque suspension and steering fasteners with the vehicle at ride height (wheels loaded) wherever a bushing is involved — tightening a control-arm or sway-bar bushing bolt with the suspension hanging pre-loads the rubber and it fails early. Clean the threads, start every fastener by hand to avoid cross-threading, and make the final pass with a calibrated torque wrench rather than an impact gun. Ball-joint and tie-rod castle nuts take a new cotter pin; never back a castle nut off to line up the hole — only tighten to the next slot.
Related lookups
- 2009 Chrysler Sebring — Full Bolt & Torque Specs
- 2009 Chrysler Sebring Caliper Bolt Torque
- 2009 Chrysler Sebring Lug Nut Torque
- Standard Torque Specs by Grade
Loading interactive lookup…